BretfordメーカーLAP30EBAの使用説明書/サービス説明書
ページ先へ移動 of 33
LAP30EBA LAP30EFR NOTEBOOK CART ASSEMBL Y Assembly Instructions for: INTERIOR E-UNIT REPOSITIONING / REPLACEMENT AND TIMER INST ALLA TION Parts List Q t y .
clip DET A I L 'A' DET A I L 'B ' E-Unit power cord bracket assembly bottom shelf Front View bracket assembly bracket assembly.
Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside.
DET A I L 'D ' Step 4 Remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'D', then carefully sliding out.
clip-rear Step 5 cutout window Reinstall the E-Units (set aside from being removed from the front) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Cross over to opposite corner of cart. 3. T ilt in and set bottom in back, in front of rear p anel cutout window .
Step 6 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf.
Step 1 Remove 18 screws (2 per shelf) from rear panel that secure the 9 interior shelves (see DET AIL 'A'). DET A I L 'A ' E-UNIT REPOSITIONING: 'REAR TO FRONT' NOTE: UNP.
Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord bracket assembly Front View Unwind the power cord of the E-Units from the cord wrap brackets (on the rer panel).
clip-rear DET A I L 'C ' DET A I L 'D ' Step 3 Remove rear-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside.
Step 4 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf.
Step 6 Reinstall the E-Units (set aside from being removed from the rear) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Position to the front of cart. 3. Tilt in and set against offset of bottom panel (of cart). 4. Grip the top and tilt to the upright position.
E-UNIT REPLACEMENT : 'REAR LOCA TION' NOTE: UNPLUG CART POWER CORDS FROM POWER SOURCE BEFORE ST AR TING Step 1 Remove 18 screws (2 per shelf) from rear panel that secure the 9 interior shelves (see DET AI L 'A').
Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord bracket assembly Front View Unwind the power cord of the E-Units from the cord wrap brackets (on the rer panel).
clip-rear DET A I L 'C ' DET A I L 'D ' Step 3 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside.
Step 4 clip-rear Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting in sideways to the top. When repositioned correctly , the E-Unit(s) power switch should be visible from rear panel cutout window .
Step 5 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf.
Step 1 E-UNIT REPLACEMENT : 'FRONT LOCA TION' NOTE: UNPLUG CART POWER CORDS FROM POWER SOURCE BEFORE ST AR TING SEE DET AIL 'A' SEE DET AIL 'B' bottom shelf E-Unit power cord bracket assembly bottom shelf Front View Open both front doors of cart to access E-Unit(s).
Step 2 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. clip DET A I L 'A' DET A I L 'B &apos.
front-right front-left Step 3 Carefully install replacement E-Unit(s) into position by placing bottom in first against the offset and tilting it in sideways to the top.
TIMER REPLACEMENT : 'E-UNIT A T REAR LOCA TION' NOTE: UNPLUG CART POWER CORDS FROM POWER SOURCE BEFORE ST AR TING DET A I L 'A ' Step 1 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DET A IL 'A').
Step 2 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. Step 3 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove bracket assembly .
Step 4 Remove filler bracket from bracket by pulling upward. Discard filler bracket. filler bracket bracket Step 5 Install timer with 2 screws. Adjust timer dial to current time.
Step 7 Reinstall the 3 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in remaining 2 shelves into position as the bottom shelf.
DET A I L 'C ' Step 8 Reinstall 6 screws to rear panel that will secure the 3 interior shelves (see DET AIL 'C'). DO NOT OVER TIGHTEN SCREWS . Installation is now complete and ready for use. Adjust timer to current time when installation is complete and ready to be plugged back into power source.
TIMER INST ALLA TION: 'E-UNIT A T FRONT LOCA TION' NOTE: UNPLUG CART POWER CORDS FROM POWER SOURCE BEFORE ST AR TING Step 1 SEE DET AIL 'A' SEE DET AIL 'B' bottom shelf clip DET A I L 'A ' DET A I L 'B' bracket assembly bracket assembly Please read and follow all instructions thoroughly.
Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside.
Step 4 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out.
Step 5 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove bracket assembly . bottom flange- bracket assembly Step 6 Remove filler bracket from bracket by pulling upward.
Step 7 Install replacement timer with 2 screws. Adjust timer dial to current time. Step 8 Install timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from the timer out the grommeted hole shown. Make sure timer face is aligned with rear panel cutouts.
notch tab Step 9 Reinstall the 3 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in remaining 2 shelves into position as the bottom shelf.
Step 1 1 bottom shelf front-right front-left Carefully reinstall E-Units into position by placing bottom in first against the offset and tilting it in sideways to the top (underneath the channel bracket of the cart top panel).
$8; $8; $8; $8; .
Part #031-6609 Rev . 08.29.05 CH Bretford 1 1000 Seymour Avenue Franklin Park, IL 60131 TEL: 847.678.2545 800.521.9614 FAX: 847.678.0852 800.343.1779 P AD LOCK - DOOR: www.
デバイスBretford LAP30EBAの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Bretford LAP30EBAをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBretford LAP30EBAの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Bretford LAP30EBAの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Bretford LAP30EBAで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Bretford LAP30EBAを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBretford LAP30EBAの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Bretford LAP30EBAに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBretford LAP30EBAデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
