ADT Security ServicesメーカーADT-UZC-256の使用説明書/サービス説明書
ページ先へ移動 of 15
D THE ADT-UZC-256 U NIVERSAL Z ONE C ODER for the Unimode ® 2020/1010, Unimode ® II and Unimode ® 4-16 Fire Alarm Control Panels Document 51349 4/25/00 Rev: A15216:D ECN 99-402 One Town Center Road Boca Raton, FL 33431 Phone: (561) 988-3600 FAX: (561) 988-3675 Security Services Inc.
Precau-Lg.p65 01/18/2000 An automatic fire alarm system –typically made up of smoke detectors, heat detectors, manual pull stations, audible warn- ing devices, and a fire alarm control with remote notification capability–can provide early warning of a developing fire.
Precau-Lg.p65 01/18/2000 WARNING - Several different sources of power can be con- nected to the fire alarm control panel. Disconnect all sources of power before servicing. Control unit and associated equip- ment may be damaged by removing and/or inserting cards, modules, or interconnecting cables while the unit is energized.
4 51349:D 4/25/00 Contents Section One: ADT-UZC-256 Universal Zone Coder ......................................................... 5 Section T wo: Board Description ......................................................................................
5 51349:D 4/25/00 Section One: ADT-UZC-256 Universal Zone Coder General The ADT-UZC-256 Universal Zone Coder provides separate codes for up to 256 initiating zones. Each code requires a different initiating circuit. Only one Notification Appliance Circuit is required, but coded output from the ADT-UZC-256 can be fed to many output circuits.
6 51349:D 4/25/00 Mounting The ADT-UZC-256 plugs into the ICA-4L in Unimode 2020/1010 systems, or mounts behind modules in the Unimode 4-16 and Unimode II. Additional Reference The ADT-UZC-256 Zone Coder can be used with the Unimode 4-16, the Unimode II, and the Unimode 2020/1010 Fire Alarm Control Panels.
7 51349:D 4/25/00 TROUBLE LED (Yellow) Lights when one or more trouble conditions are detected. ALARM TEST (Red) Follows the main coded output. SLC ON-LINE LED (Green) Blinks during communication with the master FACP. 9V POWER CONNECTOR for powering the ADT-UZC-256 during remote programming.
8 51349:D 4/25/00 Figure 3-1: Mounting the ADT-UZC-256 to a CHS-4 Section Three: Installing the ADT-UZC-256 Unimode II Installation Mechanical Installation The ADT-UZC-256 mounts beneath the third and fourth modules, to the right of the CPU.
9 51349:D 4/25/00 Unimode 4-16 Installation Mechanical Installation In a Unimode 4-16, the ADT-UZC-256 mounts beneath the third (right most) module. The ADT-UZC-256 fastens to the back of the box using three hex standoffs (one aluminum and two nylon provided), which are screwed into the three female PEM nuts as shown.
10 51349:D 4/25/00 Unimode 2020/1010 Installation Mechanical Installation In a Unimode 2020/1010, the ADT-UZC-256 plugs into a slot on the ICA-4L chassis. If the Unimode 2020/1010 is in an A-size cabinet (only one ICA-4L), the ADT-UZC-256 mounts beneath the CPU or the SIB.
11 51349:D 4/25/00 Section Four: Power/NAC Configurations These two Notification Appliance Circuits share 3.0 amps of coded power. NOTE: Cable from MPS to ADT-UZC-256: P/N 71093; all others: P/N 71091. These two Notification Appliance Circuits share 3.
12 51349:D 4/25/00 These two Notification Appliance Circuits share 3.0 amps of coded power. These two Notification Appliance Circuits share 3.0 amps of coded power. These eight Notification Appliance Circuits share 3.0 amps of coded power. These two Notification Appliance Circuits share 3.
13 51349:D 4/25/00 Section Five: Unimode 2020/1010 / ADT-UZC-256 Configuration MPS-24A Bell Power BATTERY BATTERY 3 AMP MAX. Universal Zone Coder ADT-UZC-256 XPM XPC-8 XPP-1 ARM-4 SLC EIA-485 ADT-LCD-80 CPU-2020 ADT-SIB-NET CRT EIA-232 CCM-1 LIB-200A UZC-2020.
14 51349:D 4/25/00 Section Six: ADT-UZC-256 Connections to M300CADT Modules System Sensor A2143-00 (Canada: N-ELR) End-of-Line Resistor, 47K, .5 watts, supervised and power-limited 24VDC Notification .
15 51349:D 4/25/00 Appendix A: Plug/Terminal Schematic Code Relay 3 Code Relay 2 Code Relay 1 Coded Outputs 32 1 Coded Output 3 Power Input 3 Coded Output 2 Power Input 2 Coded Output 1 Power Input 1.
デバイスADT Security Services ADT-UZC-256の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
ADT Security Services ADT-UZC-256をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはADT Security Services ADT-UZC-256の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。ADT Security Services ADT-UZC-256の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。ADT Security Services ADT-UZC-256で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
ADT Security Services ADT-UZC-256を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はADT Security Services ADT-UZC-256の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、ADT Security Services ADT-UZC-256に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちADT Security Services ADT-UZC-256デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
