BurleyメーカーG4237/8の使用説明書/サービス説明書
ページ先へ移動 of 15
BURLEY G423 7 / 8 IM A GE FL UELESS GA S HEA TER INST ALL A TION, SERVICING & US ER INS TRU CTIONS FOR USE IN THE COUNT RIES S T A TED ON THE DA T A PL A TE AND C ART ON WITH NA TUR AL GAS G20 OR .
- 2 - INTRODUCTION Thank you for choosing this b urley product. All of our pro ducts c arry a CE ma rk which is awarded by an i ndependent test house (notified body ) and shows the fires have be en type tested to meet the essential requirements of the European Gas Appliance Directive and the appro priate British Standards.
- 3 - 3. GENERAL REQUIREMENTS 3.1 Gas appliances must be installed i n ac cordance with the rules in f orce. I n the UK it is the law that a ll gas a ppliance s must be i nstalled by a CORGI registered installer, i n ac cordance with the Gas Safety (Installation and U se) re gulations (as amended).
- 4 - 4.2 D ecide upon the route f or the gas supply and if this i s to be a conce aled supply, s elect a suitable hole in the fire box , remove t he knock out an d lay in the s upply as required. F it the rubber grommet aro und the gas pipe entry to the appliance and seal.
- 5 - ensure there is no possibili ty of them touching the appliance . 632mm 197mm 590mm Overall dimensions are as shown. Hearths - Fo r hea rth mounting ( or if the fire is less than 20 0mm above the ground) then the hearth must protrude at least 100mm in f ront of the fire and 50mm to either side.
- 6 - 5.3 METHOD TWO - INSET ON HEAR TH OR INSET WALL MOUNTED This method allows f or the fire to be inset into a wall or fire place opening. The applia nce c ase has a 90mm deep spacer that needs to be remove d and the corr esponding deep bracke ts nee d to be taken off the case.
- 7 - Fixing - The a ppliance should be sec ured to the wall usi ng the fixing bracke ts on t he fla nge of the appliance. If it is to be mo unted above t he ground, c are should be taken to e nsure the wall is a ble to take the we ight of the appliance an d that the fixings are o f the c orrect type.
- 8 - 7.0 REASSEMBLY 7.1 To remove the g lass, remove the 4 nuts i n t he side frame s and pivotin g it out from the bottom remove glass from its top channel . Refitting is done in revers e order. 7.2 REVERSIBLE SIDE CHEEKS The appliance has side c heek s that are plain on one side and bri ck effect on the other.
- 9 - 9.0 TO LIGHT THE HEAT ER BEFORE L I GHTING. IF THE PIPES HAVE N OT BEEN PURGED OF DEBRIS, DO SO NO W BE FORE LIGHTING THE FIRE. FAILURE TO DO SO WILL RESULT IN BLOCKAGES WITHIN THE PILOT. BURLEY A PPLIANCES IS THE ONLY COMPANY TO BENCH RUN AND THOROUGHLY TEST EVERY SINGLE GAS F IRE IT PRODUCES.
- 10 - automatically l ight the pilo t light, mo nitor its sa fety f or about 20 seconds and then it will light the burner on high flame. To alternate between high and low fl ame use the flam e buttons on t he right hand side of the handset. To turn the fire OFF press the ● button on the top left hand side of the remote handset.
- 11 - 10.4 FIREFRO NTS The design of these affec t combustion, therefore only the corr ect front supplied with the appliance may be fitted. 10.5 FIREGUA RDS A fir eguard is not supplied with this app.
- 12 - Light t he fire using the method i n the i nstructions and ensure that the pilot lights consiste ntly an d the pilot flame enve lopes the thermo couple. The pilot should hold in 10 seconds. Turn c ontrol to main burner, this should light smoothly within 10 s econds.
- 13 - This is not a dr yin g appliance. Do no t place clothing or other arti cles, on or ag a inst it. Do not store or use flamm a ble substances on or ne ar the heater. Do not spra y aerosols on or near the heater. If any material, such as plast ic, melts o nto the surface of the glass, turn the heater off and allow it to co ol.
- 14 - To light the fire, f irst ensure the red knob is turned clockwise to OFF . Press the left hand (red) control knob for several seconds then turn slowly a nticlockwise to the ignition position. A click will be heard and the pilot (under right side of fuel bed) should light.
- 15 - CLEANING AND MAIN TENANCE Ensure the appliance is switched off and cooled down before cleaning. The case and surround are best cleaned with a damp cl oth a nd wiped dry to avoid smearing.
デバイスBurley G4237/8の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Burley G4237/8をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBurley G4237/8の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Burley G4237/8の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Burley G4237/8で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Burley G4237/8を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBurley G4237/8の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Burley G4237/8に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBurley G4237/8デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
