CanonメーカーL2000の使用説明書/サービス説明書
ページ先へ移動 of 19
CANON FAX – L2000 SIMPLIFIED GUIDE.
1 CONTENTS PAGE SUPER G3 FAX-L2000 I To Regis ter Sender’s Id entifi cation 3 II Sending Docum ents 4 III Setting Up Speed Dialing A One-to uch Sp eed Dial 5 B Coded Speed Dial 6 C Group Dial 7 IV T.
2 PAGE SUPER G3 FAX-L2000 XII Setting Up T ransmission (T X) Report For Every Document Sent Out 16 XIII Erasing A Docum ent That Is Queuing To Be Sent F r o m T h e M e m o r y 1 7 XIV Check The Statu.
3 I TO REGISTER SENDER IDENTIFI CATION I. INPUT YOUR FAX NUMBER AND COMPANY NAME 1. Open all three all three panel covers 2. Press Data Reg istrati on 3. Press ▼ until display shows “ 3. FAX SETTINGS” 4. Press OK to d isp lay “1. USER SETTINGS” 5.
4 II SENDING A DOCUMENT A. DIRECT SENDING 1. Place documents face up on the feeder 2. Press DIRECT TX (indicator lights up) 3. Enter fax num ber 4. Press START B. MEMORY SENDING 1. Place documents face up on the feeder 2. Make sure DIRECT TX is “off” 3.
5 III TO STORE FAX NUMBERS A. ONE-TOUCH SPEED DIAL ( 01-KEY TO 72-KEY ) 1. Open all three panel covers 2. Press Data Reg istrati on 3. Press ▼ until display shows “ 4. ADD. REGISTRATI ON ” 4. Press OK twice 5. Press ▼ (if necessary) until an em pty space appears 6.
6 B. CODED SPEED DIAL ( *000 TO *127 ) 1. Open all three panel covers 2. Press Data Reg istrati on 3. Press ▼ until display shows “ 4. ADD. REGISTRATI ON ” 4. Press OK 5. Press ▼ to display “ 2. CODED SPD DIAL ” 6. Press OK 7. Press ▼ (if necessary) until an em pty space appears 8.
7 C. TO PROGRAM GROUP DIAL 1. Open all three panel covers 2. Press Data Reg istrati on 3. Press ▼ until display shows “ 4. ADD. REGISTRATI ON ” 4. Press OK 5. Press ▼ to display “3 . GROUP DIAL ” 6. Press OK 7. Press ▼ (if necessary) until an em pty space appears 8.
8 IV TO ERASE A SPEED DIAL A TO CANCEL A NUMBER IN THE ONE-TOUCH SPEED DIAL 1. Follow steps A. 1 . to A.4. (Refer to III : TO STORE FAX NUMBERS: ONE-TOUCH SPEED DIAL) 2. Close all three panel covers & press desired one-touch key 3. Press OK twice 4.
9 V SENDING TO MORE THAN ONE LOCATION (SEQUENTIAL BROADCASTING) A. USING ONE-TOUCH / CODED SPEED DIAL 1. Place documents face up on the feeder 2. Press all the relevant one-touch / coded-dial numbers one right after another 3. Press START 4.
10 VI TO SEND DOCUMENTS AT A LATER TIME (DELAYED TRANSMISSION) 1. Open all three panel covers 2. Press Delayed Transm ission 3. Enter the desired tim e (tim e set must be w ithin 24 hours from the tim e on the display) 4. Press OK 5. Enter the fax num ber(s) 6.
11 VII WHEN THE FAX DISPLAYS “RECEI VED IN MEMORY” Display screen flashes message “ RECEIVED IN MEMORY ” repeatedly . 1. Supply paper to the paper cassette if display prom pts “ SUPPLY REC.
12 VIII RE-SEN DING IF No.V II ABOV E IS NOT P OSSIBLE, EACH DOCUMENT RECEIVED IN THE MEMORY CAN BE RE-SENT INDIVIDUALLY TO ANOTHER DESTINATION FOR PRINTING 1. Open all three panel covers 2. Press Memory Reference 3. Press ▼ to display “ 4. RESEND DOCUMENT ” 4.
13 IX TO PRINT REPORTS AND LISTINGS A . SPEED DIAL LIST 1. Open all three panel covers 2. Press Report 3. Press ▼ to display “ 2. SPEED DIAL LIST ” 4. Press OK 5. Press ▼ to search for desired list i.e. “1. 1-TOUCH LIST”, “2. CODED DIAL LIST” or “3.
14 X MAKING COPIES 1. Place docum ents face up on the feeder 2. Press COPY 3. Press ▼ to select paper cassette, if required 4. Ent er the n umber of cop ies requ ired (0 1 to 99) To re-enter the num ber, press C 5.
15 XI CONFIRMATI ON REPORT To Request For A Tr ansmission (T X) Report Only For One Particular Sending Setting up the Program One-Touch Key 1. Open all three all three panel covers 2. Press Data Reg istrati on 3. Press ▼ until display shows “ 3. FAX SETTINGS” 4.
16 XII TRANSMI SSION REPORT To set up Transm ission (TX ) Report For Every Docum ent Sent Out 1. Open all three panel covers 2. Press Data Reg istrati on 3. Press ▼ until display shows “ 3. FAX SETTINGS ” 4. Press OK 5. Press ▼ to display “ 2.
17 XIII ERASING A DOCUM ENT FROM THE M EMORY A. Using the DELETE FILE Button 1. Press Delete File 2. Press ▼ to select the desired TX/RX number to be deleted 3. Press OK 4. Press * to confirm deletion B. Using The Mem ory Reference Button 1. Press Memory Reference 2.
18 XIV TO CHECK THE STATUS OF A FAX TRANSACTION A. The Status Of A Pending Job 1. Press Monitor 2. Press OK to check the status of a transaction 3. Press ▼ to select the list of TX/RX jobs 4. To end, press Stop B. The Result after Sending / Receiving 1.
デバイスCanon L2000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Canon L2000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCanon L2000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Canon L2000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Canon L2000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Canon L2000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCanon L2000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Canon L2000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCanon L2000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。