CarrierメーカーASPB07-1SIの使用説明書/サービス説明書
ページ先へ移動 of 8
® Turn to the Expertg Installation Guide This Installation Guide is intended to be used in conjunction with the Owner's Manual. The Owner's Manual must first be read thoroughly prior to installation of the Home Standby generator. A_ intended for outdoor installation only.
® Turn to the Expertg ELECTRICAL INTERCONNECTION DRAWING GENERATOR GROUND (LOCATED ON THE REAR OF UNIT) N1 N2 23 194 GENERATOR OUTPUT CIRCUmT BREAKER 2 POLE / EARTH SPIKE "_ / / / I /.
TO HOUSE BRANCH CiRCUiTS SPLICED USING WiRE NUTS EMERGENCY CiRCUiTS IllU 40A OR 70A 2-POLE CIRCUIT BREAKER i SERVICE CONNECTION BOX EXTERNAL CUSTOMER 4 PmN CONNECTOR BAR UL LISTED PANEL BOARD (8,10,12.
Thank you for purchasing this model of the CARRIER product line. This model is a compact, high performance, air-cooled, engine-driven generator designed to automatically supply electrical power to operate critical loads during a utility powerfailure.
Never use the generator or any of its parts as a step. Stepping on the unit can stress and break parts, and may result in dangerous operating conditions from leaking exhaust gases, fuel leakage, oil leakage, etc. ELECTRICAL HAZARD All generators covered by this manual produce dangerous electrical voltages and can causefatal electrical shock.
. 6. 7. 8a, 8b. It will be necessary to pay a visit to your local municipaloffices to apply for a building permit. Building permits are necessary to ensure proper installation, safety and adherence to all local building code specifications. The location and phone number can befound in the government section of your local phone book.
ID Theouterdiameter of thethreaded end is 15/16". lOa. lOb. lla. llb. llc. Determine where the flexible conduit will pass through the house from inside to outside. When you are certainyou have clearance on each side and within the wall, drill a small pilot holethrough the wall to markthe location.
- continued frompage7 Wire nut the black wire to the matching circuit lead wire from the emergency circuit breaker from load center in the transfer switch. (Allcircuit wires are color coded and labeled for easy identification). UL approved wire Iocknuts are included in installation kit.
デバイスCarrier ASPB07-1SIの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Carrier ASPB07-1SIをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCarrier ASPB07-1SIの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Carrier ASPB07-1SIの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Carrier ASPB07-1SIで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Carrier ASPB07-1SIを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCarrier ASPB07-1SIの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Carrier ASPB07-1SIに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCarrier ASPB07-1SIデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。