CDAメーカーECHK90の使用説明書/サービス説明書
ページ先へ移動 of 20
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .
2 Important The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CD A reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment.
3 safety (L VD) and Electromagnetic interference compatibility (EMC). IMPORT ANT INFORMA TION FOR CORRECT DISPOSAL OF THE PRODUCT IN A CCORD ANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer providing appliance recycling services.
4 • This extractor has been designed to be used in a room with a volume of less than 36m. • Steam cleaners must not be used when cleaning this appliance.
5 Using your Extractor For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for appro ximately 15 minutes after the end of cooking. Control Panel A - Power o button B - Speed level buttons C - Light button T o switch the extractor light on or o • Press button “C” .
6 Care and Maintenance IMPORT ANT : DO NO T PERFORM MAINTENANCE OR CLEANING OF THE EXTRA CT OR WITHOUT FIRST SWIT CHING OFF THE ELECTRICITY SUPPL Y . Cleaning Y ou should use a non-abrasive cleaner . Any abrasive cleaner (including Cif ) will scratch the surface and could erase the control panel markings.
7 position to prevent damage from other items in the dishwasher . After rinsing and drying, replace the filters. T o remove the grease filters, pull open the handle on the grease filter . It will release at the handle side. Then lower the grease filter to remove it completely .
8 Changing the Light IMPORT ANT : DO NO T PERFORM MAINTENANCE OR CLEANING OF THE EXTRA CT OR WITHOUT FIRST SWIT CHING OFF THE ELECTRICITY SUPPL Y . DO NO T CHANGE THE LIGHT BULB IMMEDIA TEL Y AFTER USE AS THE BULB WILL BE HO T . ALL OW IT T O COOL BEFORE REMOVING IT .
9 Bulb replacement is not covered by the guarantee. Only use bulbs recommended for your extractor . Do not fit bulbs of a higher power rating. Bulbs of a lower power rating may be adequate for use, generally last longer and use less energy .
10 your hob being disconnected from the gas supply and the installation being reported to RIDDOR (The height should be measured from the top of the burners). IN THE ABSENCE OF ANY INSTRUCTIONS SUPPLIED WITH THE GAS HOB, THE MINIMUM DIS T ANCE BETWEEN THE HOB AND EXTRA CT OR MUST BE A T LEAS T 760mm.
11 Installation Note • W e recommend that you seek the help of another individual when installing this product. • The fixings supplied are suitable for most installations. It is the responsibility of the installer to ensure that the fixings are suitable for the ceiling type in the property .
12 Fig. 9 calculation shown below for your extractor (refer to fig 4): A = Height of gas hob burner or electric hotplate height from the kitchen floor B = Clearance required: Gas hobs 750mm recommended Electric hobs: 650mm recommended A+B is the required height of the body of the extractor above the floor .
13 be at least the minimum height specified) 5. Place the chimney section over the body assembly , as shown in fig 8. 6. With the help of another individual, raise the whole assembly to the ceiling and fix securely in place using four screws appropriate for the wall plugs inserted in step 2.
14 Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED T O THE MAINS SUPPL Y B Y A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWIT CHED FUSED SPUR OUTLET AND PROTECTED B Y A 3A FUSE. W e recommend that the appliance is connected by a qualified electrician, who is a member of the N.
15 NO TE: USE A 3A FUSE Assembly and electrical connection should be carried out by competent personnel. When installing this product we recommend you seek the help of another individual.
16 T roubleshooting If your extractor is not working: 1. Check that the mains supply has not been switched o . 2. Check that the fuse in the spur has not blown. Contact CD A Customer Care A: Customer Care Department, The CD A Group Ltd, Harby R oad, Langar , Nottinghamshire, NG13 9HY T : 01949 862 012 F: 01949 862 003 E: service@cda.
17.
18.
19 E & O E. All instructions, dimensions and illustrations are provided for guidance only . CDA reserve the right to change specifications without prior notice. Attribute Symbol Units Model Identification echk90 ecpk90 Annual Energy Consumption AEC Hood 84.
Please contact our Customer Care Department, or for Service on the details below . Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www.
デバイスCDA ECHK90の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
CDA ECHK90をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCDA ECHK90の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。CDA ECHK90の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。CDA ECHK90で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
CDA ECHK90を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCDA ECHK90の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、CDA ECHK90に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCDA ECHK90デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。