Chicago Electricメーカー97588の使用説明書/サービス説明書
ページ先へ移動 of 21
MAGNESIUM HEA VY DUTY 7” ANGLE GRINDER 97588 SET UP AND OPERA TING INSTRUCTIONS Distributed exclusively by Harbor Freight T ools ® . 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our website at: http://www .harborfreight.com Read this material before using this product.
SKU 97588 For technical questions, please call 1-800-444-3353. Page 2 SA VE THIS MANUAL Keep this manual for the safety warn- ings and precautions, assembly , operat- ing, inspection, maintenance and cleaning procedures.
SKU 97588 For technical questions, please call 1-800-444-3353. Page 3 plugs with grounded power tools. Unmodied plugs and matching out - lets will reduce risk of electric shock. A void body contact with grounded b. surfaces such as pipes, radiators, ranges and refrigerators.
SKU 97588 For technical questions, please call 1-800-444-3353. Page 4 proved for the specic hazards in the work area. Power tool use and care 4. Do not force the power tool. Use a. the correct power tool for your ap- plication. The correct power tool will do the job better and safer at the rate for which it was designed.
SKU 97588 For technical questions, please call 1-800-444-3353. Page 5 mum speed marked on the power tool. Accessories running faster than their RA TED SPEED can break and The outside diameter and the 5. thickness of your accessory must be within the capacity rating of your power tool.
SKU 97588 For technical questions, please call 1-800-444-3353. Page 6 could snag your clothing, pulling the accessory into your body . Regularly clean the power tool’ s 14. air vents. The motor ’s fan will draw the dust inside the housing and ex - cessive accumulation of powdered metal may cause electrical hazards.
SKU 97588 For technical questions, please call 1-800-444-3353. Page 7 manual cannot cover all possible con- ditions and situations that may occur . It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator .
SKU 97588 For technical questions, please call 1-800-444-3353. Page 8 side of cut-off wheel. Abrasive cut- off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter . Always use undamaged wheel 4. anges that are of correct size and shape for your selected wheel.
SKU 97588 For technical questions, please call 1-800-444-3353. Page 9 Grip tool as lightly as possible (while 6. the tool do the work.
SKU 97588 For technical questions, please call 1-800-444-3353. Page 10 Double Insulated T ools: T ools with T wo Prong Plugs T ools marked “Double Insulated” do 1.
SKU 97588 For technical questions, please call 1-800-444-3353. Page 1 1 RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120/240 VOL T) NAMEPLA TE AMPERES (at full load) EXTENSION CORD LENGTH 25’ 50’ 75’ 100’ 150’ 0 – 2.0 18 18 18 18 16 2.
SKU 97588 For technical questions, please call 1-800-444-3353. Page 12 SPECIFICA TIONS Electrical Requirements .
SKU 97588 For technical questions, please call 1-800-444-3353. Page 13 Installing the Auxiliary Handle TO PREVENT SERIOUS INJUR Y : Do not operate this tool with one hand only or without the Auxiliary Handle properly installed. The Auxiliary Handle may be installed 7.
SKU 97588 For technical questions, please call 1-800-444-3353. Page 14 Closely inspect the Grinding Wheel 4. before mounting. Perform a ring-test on the wheel (unless wheel is smaller than 4” or is an unusual shape) as follows: a.
SKU 97588 For technical questions, please call 1-800-444-3353. Page 15 W ork Piece and W ork Area Set Up Designate a work area that is clean 1. and well-lit. The work area must not allow access by children or pets to prevent injury and distraction. Route the power cord along a safe 2.
SKU 97588 For technical questions, please call 1-800-444-3353. Page 16 MAINTENANCE AND SER VICING Procedures not specically explained in this manual must be performed only by a qualied technician.
SKU 97588 For technical questions, please call 1-800-444-3353. Page 17 b. as shown in the illustration above. c. Use a small prying tool (not includ- ed) to hold the Spring Clips to the side while you remove the carbon brushes.
SKU 97588 For technical questions, please call 1-800-444-3353. Page 18 T roubleshooting Problem Possible Causes Likely Solutions T ool will not start No power at outlet. 1. Cord not connected. 2. Carbon Brushes may be worn or 3. damaged. Check power at outlet.
SKU 97588 For technical questions, please call 1-800-444-3353. Page 19 P ARTS LIST Part Description Qty . 1 Outer Flange Arbor Nut 1 2 Grinding Wheel (not included) - 3 Inner Flange 1 4 Quick Release .
SKU 97588 For technical questions, please call 1-800-444-3353. Page 20 ASSEMBL Y DIAGRAM Record Product’ s Serial Number Here: Note: If product has no serial number , record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only , and are not avail- able individually as replacement parts.
SKU 97588 For technical questions, please call 1-800-444-3353. Page 21 REV 1 1h 90 DA Y W ARRANTY Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and durabil.
デバイスChicago Electric 97588の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Chicago Electric 97588をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはChicago Electric 97588の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Chicago Electric 97588の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Chicago Electric 97588で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Chicago Electric 97588を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はChicago Electric 97588の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Chicago Electric 97588に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちChicago Electric 97588デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
