CMA DishmachinesメーカーL-1Xの使用説明書/サービス説明書
ページ先へ移動 of 18
www.cmadishmachines.com 800-854-6417 FAX 714 - 8 95 - 2 141 CMA DISHMACHINES 12700 KNOTT AVENUE GARDEN GROVE, CALIFORNIA 92841 MODEL L-1X & L-1X16 Installation & Operations Rev 1.
T ABLE OF C ONTENTS M ODEL CMA-L-1X & L-1X16 1. SPECIFICAT IONS ......................................................................................... 2 1.1. L-1X & L-1X 16 ...................................................................
1. S pecifications METRIC EQUIVALENT 1.1. L-1X & L-1X16 WATER CONSUMPTION PER RACK 1.7 GAL. 6.44 L PER HOUR 40.8 GAL. 154.4 L OPERATING CYCLE WASH TIME-SEC 57 57 RINSE TIME-SEC 48 48 DWELL TIME-SEC 15 15 TOTAL CYCLE 2 MIN. 2 MIN. OPERATING CAPACITY RACKS PER HOUR 24 24 WASH TANK CAPACITY 1.
1.2. L-1X and L-1X16 Operational Cycle The L-1X and L-1X16 Operational Cycle ha s a total cycle time of 2 minutes (120 seconds). The Timing Diagram and the steps listed below detail the individual functions that are executed during each Operational Cycle.
allowing time for the machine to refill e nough to avoid running the pump dry before the pump motor restarts and runs to th e completion of the operational cycle.
Getting Started 2. Getting S t arted All sections of the manual addres s both the L-1X and the L-1X16. Separate information o n each machine is only provided where differe nce s exist between the two models.
Getting Started 2.2. Receiving and Installation The dishwasher is shipped from the factory in a corrugated box on a woo den pallet. The installation guidelines give a systematic pro cedure for setting up the machine. 1. Start by removing the box and packaging materi al.
Getting Started 2.2.4. Installers Checklist Dishmachine checked for concealed damage Hot water supply is 140° F (60 C) Incoming water supply line is ½” minimum Supply circuit break.
Operation 3. Operation 3.1. Initial Setup 3.1.1. Check… Drain screen is in place Spay arms and end plugs are secure 3.1.2. Chemicals • Assure there is a sufficient supply of chemicals before beginning a shift.
Operation These cams were set at the factory but can b e adju sted after final installation to maximize efficiency of chemical use (see section 4.1.1 Cam Adj ustment .) 3.2.3. Proper Filling The amount the machine is automatically f illed each cycle is determined by the numbe r 4 cam.
Maintenance 4. Maintenance The maintenance proced ures detail ed in this sect ion are to be performed by quali fied personnel. 4.1. Timer assembly The standard timer assembly con sist s of a ½ RPM (2 minutes per revolution) motor turnin g a common shaft, which, in turn, rotates eight cams.
Maintenance 4.2. Quick service guide MODEL L-1X & L-1X16 P ARTS MANUAL Rev. 1.14 Page 11 MODELS: L-1X, L-1X16 UNDER COUNTER TECHNICA L ISSUE CAUSE SOLUTION Delimer switc h in delime position Flip to NORMAL position Wash Pump motor will not shut off Faulty delimer switch Replace switch, P/N 00475.
Maintenance 4.3. Troubleshooting PROBLEM LIKELY CAUSE SOLUTION Power off at circuit breaker Reset circuit breaker Defective power swit ch Replace power switch P/N: 00433.10 Machine inoperative Defective timer assembly motor Replace timer assembly motor P/N: 00501.
Maintenance PROBLEM LIKELY CAUSE SOLUTION Turn up supply water heate r Low incoming water temperature (below 140° F) Insulate supply water pipe Thermostat out of adjustment Adjust thermostat (Optional) sustainer heate r not installed Install (optional) sustainer heater P/N: 04109.
Maintenance PROBLEM LIKELY CAUSE SOLUTION Defective rinse pump motor Replace pump motor P/N: 00416.00 Rinse pump does not run Defective timer assembly (Cam 6) Replace timer assembly * P/N: 00408.80 Defective sani/detergent primer switch Replace primer switch P/N: 03470.
Addendum 5. Addendum for Machines Inst alled in the City of Chicago “All food dispensing e stablishments using chlorine o r other approved chemical sanitizers shall, at all times, maintain an adequate testing devi ce.
Appendix A: Operator & Cleaning Instructions MODEL L-1X & L-1X16 INST ALLATION & OPER ATION M ANUAL Rev. 1.14 Page 16.
ELECTRICAL DIAGRAM 6. Electrical Diagram MODEL L-1X & L-1X16 INST ALLATION & OPER ATION M ANUAL Rev. 1.14 Page 17.
デバイスCMA Dishmachines L-1Xの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
CMA Dishmachines L-1Xをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCMA Dishmachines L-1Xの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。CMA Dishmachines L-1Xの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。CMA Dishmachines L-1Xで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
CMA Dishmachines L-1Xを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCMA Dishmachines L-1Xの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、CMA Dishmachines L-1Xに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCMA Dishmachines L-1Xデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
