Crimestopper Security ProductsメーカーCS-2004DC IIの使用説明書/サービス説明書
ページ先へ移動 of 24
SERIES II CS-2004TW1 with 2-Way AM Pager/Remote & 1-Way ‘Sidekick’ Remote CS-2004DC II with two 1-Way Remotes INSTALLATION & OPERATING INSTRUCTIONS CONGRATULATIONS on your choice of a Security System by Cr imestopper Security Products Inc.
TABLE OF CONTENTS Installation Cautions & Warnings…….……………………………………………………………...………………2 Suggested Component Mounting………….…………………………………………………………….
CONTROL MODULE / COMPONENT MOUNTING DO NOT Mount the control unit or wiring harness in the engine compartment or anywhere they can become entangled with moving parts such as brake/gas/clutch pedals, or the steering column. The alarm control module should be mounted in a concealed location.
WIRING BLUE WIRE: (-) HOOD/TRUNK TRIGGER The Blue wire is used for a grounding hood pin switch, trunk pin or both. Connect to existing hood and trunk pin switches that read ground when open. If no existing switches are available, install new pin switches if desired.
WIRING BLACK/WHITE WIRE: (+/-) OUTPUT FROM ON-BOARD 15A RELAY (Term #30, Step #3) Connect this wire to your Auxiliary device or Function. The function of this output depends on the connection of the Gray wire and the polarity of this output matches the White/Red wire.
WIRING MINI PLUGS: 2-PIN PLUG (SMALL): LED INDICATOR (RED FLASHING LIGHT) 2-PIN PLUG (LARGE): PROGRAM/OVERRIDE PUSH BUTTON TIP: The Sensor supplied with this system does not require any additional wiring, simply mount the sensor in a suitable location, plug in, and adjust to the desired levels of sensitivity.
WIRING BROWN/BLACK WIRE: (-) AUX. OUTPUT #1 OR M.A. P.-Mobile Accessories Protection (Optional) This is a programmable output wire that can operate two different ways: 1. 2. (DEFAULT Operation) A Remote Auxiliary Output that provides a ½ Second (-) Negative pulse when Button #3 is pressed and released to open a power trunk or hatch releas e.
POWER DOOR LOCK WIRING 6-PIN DOOR LOCK PLUG 18 GA. (Optional / ON-Board Relays): VIOLET: DOOR LOCK Relay Term. #87: Normally Open [Polarity Input for Lock relay] WHITE: DOOR LOCK Relay Term. #30: Common [Lock Output] GRAY: DOOR LOCK Relay Term. #87A: Normally Closed VIO/WHT: DOOR UNLOCK Relay Term.
POWER DOOR LOCK DIAGRAMS UL REVERSE P OLA RITY DOOR LOCK WIRING + L NEGA TIVE TRIGGER D OORLOCK WIRING UL L NOT USED UNLO CK W I RE CUT LOCK W I RE CUT FAC T O RY LOCKING RELA YS UL L + A F TERMA RKET.
STARTER DISABLE WIRING STARTER DISABLE PLUG: (3) ORANGE 14 GA. WIRES: (PROGRAMMABLE: Normally Closed or Normally Open Configuration with ON-Board Relay ) Note: READ BELOW before connecting starter disable! Norm ally OPEN must be programmed to operate.
SYSTEM WIRING DIAGRAM IGNITION ST ARTER SWITCH PA R K I N G LIGHTS (+/-) On -Board Relay BA TTER Y - BLACK/WHITE 15A On-b oar d WHITE/RED GRA Y CUT IGNITION + SWITCH + CAR-JACK ENABLE OUTPUT (-)HOOD/T.
CS-2004TW1 ANTENNA The following diagram pertains to the CS-2004TW1 two-way paging model only: WINDSHIELD ANTENNA LOCA TIONS CS-2004TW1 Black P lug Blue Plug RECOMMENDED Note Orientation of Black & Blue Pl ugs.
OPTION PROGRAMMING You can program each option individually or multiple options in one session. You may start with the lowest option # and continue on to higher options without repeating the steps #1 through 3. To Engage Option Programming: 1. Turn Key to the ON position.
OPTION PROGRAMMING 1. AUTOLOCK WITH IGNITION This option controls whether the doors will automatically lock when the ignition is t urned on and will unlock when the ignition is turned off. 2. PASSIVE ARMING This option controls the Passive (Automatic) arming feature.
OPTION PROGRAMMING 9. OPEN DOOR/ZONE WARNING (5 or 60 Seconds) This setting changes the delay time in which the alarm system begins to monitor the Door Zone. This is helpful on vehicles with delayed dome lights. It prevents the alarms warning chirps due to extended dome light circuit.
CS-2004TW1 / CS-2004DC II REMOTE PROGRAMMING TRANSMITTER PROGRAMM ING NOTES (Read first!): (1) The CS-2004TW1 will learn up to 4 remotes, any co mbination of special CS-398TW 1-Way or CS-389LED 2- Way pager remotes. (2) The CS-2004DC II will up to 4 CS-404TX remotes.
CS-2004TW1 / CS-2004DC II REMOTE PROGRAMMING IGN OFF WAIT F O R 4 FL A SHES PRESS 4 X's FLA SH 2, 3, or 4 X' s IGN OFF PRESS TOGETHER "TW 1" OR SLNT AU X "DC" PRESS LOCK .
OPERATION SLNT AUX ARM/ DISARM/ UNLOCK LOCK PA G I N G LED's SILENT/ AUX. 2 ANTENNA FIXED AUX. 1 #1 #2 #3 #4 CS-2004T W1 LED P AG ING REM OTE CS-2004DC II / CS-2004TW1 remote controls: SLNT #3 #1 #2 #4 LOCK TRU NK SILENT/ UNLOCK VEHICLE 2 FLA SHLIGHT AU X .
OPERATION ACTIVE ARMING To arm the alarm and lock the doors, press the #1 Button on any remote. You will hear a single siren chirp and the lights will flash once. The system will arm, the doors will lock (optional) and the starter will be disabled. The red in- dash LED in the vehicle will begin to flash.
OPERATION SHOCK / IMPACT PROTECTION WITH PRE-WARNING Once the system is armed, if a low-level shock to the v ehicle body is detected, the pre-warning sensor activates with 5 siren chirps and one light flash as a Warn-Away feature. If a hard impact to the vehicle is detected the system will go into a full trigger cycle for 20 seconds.
OPERATION PASSIVE ARMING / PASSIVE LOCK MODES (PROGAMMABLE) If programmed, passive (Automatic) Arming will occur 30 Se conds after the ignition is turned off and the last door has been closed. The lights will flash twice when the last door is closed and the LED will begin flashing rapidly while counting down.
OPERATION CS-2004TW1 LED TRANSCEIVER (LOW BATTERY WARNING) CR2032 3V Lithium Battery T wist and Remove Battery cover w ith a Coin or Screwdriver Larger "+" Posi tive side of battery faces up CS2004TW1 BA TTER Y REPLACEMENT The CS-2004TW1 LED has a low battery warning system.
2-VEHICLE OPERATION: (CS-2004DC II SYSTEM ONLY) 2-Vehicle method (CS-2004DC II SYSTEM ONLY): Your CS-2004DC II remote includes a push-button on the side for 2-car operation. You can only operate a second vehicle with a CS-2004DC II system installed. Your remote must be programmed to the second vehicle first.
CARJACK PROTECTION PROGRAMMABLE PASSIVE CARJACK This feature provides Passive Carjack protecti on and must be enabled before use through Alarm programming options #7 & #12 on page 13. We recommend this mode should only be used in serious situations.
デバイスCrimestopper Security Products CS-2004DC IIの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Crimestopper Security Products CS-2004DC IIをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCrimestopper Security Products CS-2004DC IIの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Crimestopper Security Products CS-2004DC IIの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Crimestopper Security Products CS-2004DC IIで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Crimestopper Security Products CS-2004DC IIを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCrimestopper Security Products CS-2004DC IIの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Crimestopper Security Products CS-2004DC IIに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCrimestopper Security Products CS-2004DC IIデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。