DeWaltメーカーDWE4599Nの使用説明書/サービス説明書
ページ先へ移動 of 20
DWE4557- XE, DWE4559- XE, DWE4597N- XE, DWE4599N- XE HEA VY -DUTY L ARGE ANGLE GRINDERS INSTRUCTION MANU AL.
.
1 Definitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injur y .
2 SAFETY INSTRUCTIONS FOR POWER TOOLS When using power tools, always obser ve the safety regulations applicable in your countr y to reduce the risk of fire, electric shock and personal injury . Read the following safety instr uctions before attempting to operate this product.
3 4) POWER TOOL USE AND CARE a) Do not force the power tool. Use the correct power tool for your application. The cor rect power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off.
4 l) Never lay the power tool down until the accessory has come to a complete stop. The spinning accessor y may grab the sur face and pull the power tool out of your control. m) Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessor y could snag your clothing, pulling the accessory into your body .
5 For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel that is entering into the pinch point can dig into the sur face of the material causing the wheel to climb out or kick out.
6 f ) Use extra caution when making a “pocket cut” into existing walls or other blind areas. The protr uding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback. Safety War nings Specific for Sanding Operations a) Do not use excessively oversized sanding disc paper .
7 other constr uction activities contains chemicals known to cause cancer , bir th defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonr y products, and • arsenic and chromium from chemically-treated lumber .
8 E-CLUTCH™ (DWE4597N- XE, DWE4599N-XE) This unit is equipped with an E-Clutch™ (Electronic Clutch ), which in the event of a high-load or wheel pinch, the unit will be shut off to reduce the reaction torque to the user . The switch needs to be cycled (turned on and off ) to restar t tool.
9 Rotating the Gear Case (Fig. 4) For applications in which a tool will be dedicated FIG. 4 for uses in edge grinding and finishing work, the gear case may be rotated 90° lef t or right of its original position. 1. Remove the four corner screws attaching the gear case to motor housing.
10 Sanding Discs r ubber backing pad sanding disc clamp nut Grinding Wheels T ype 27 guard T ype 27 hubbed wheel T ype 28 guard T ype 28 hubbed wheel T ype 28 guard backing flange T ype 28 non-hubbed .
11 T ype 1 guard OR T ype 27 guard backing flange abrasive cutting wheel outer flange washer clamp nut T ype 1 guard OR T ype 27 guard backing flange diamond cutting wheel outer flange washer clamp nut Cutting Wheels Alternative guards can be purchased at an additional cost.
12 CAUTION: Make sure the wheel has come to a complete stop be fore setting the tool down. SPINDLE L OCK BUT TON (FIG. 9) The spindle lock button (D) is provided to prevent the spindle FIG.
13 3. Position yourself so that the open-underside of the wheel is facing away from you. 4. Once a cut is begun and a notch is established in the workpiece, do not change the angle of the cut. Changing the angle will cause the wheel to bend and may cause wheel breakage.
14 4. Move the tool constantly in a straight line to 5 ˚ –15 ˚ FIG. 15 prevent burning and swirling of work sur face. Allowing the tool to rest on the work sur face without moving, or moving the tool in a circular motion causes burning and swirling marks on the work sur face.
15 USING WIRE CUP BRUSHES AND WIRE WHEELS (FIG. 16) Wire wheels and br ushes can be used for removing rust, scale and paint, and for smoothing irregular sur faces. NOTE: The same precautions should be taken when wire br ushing paint as when sanding paint (refer to Precautions T o T ake When Sanding Paint ).
16 MOUNTING CUTTING WHEELS (FIG. 22) CAUTION: Matching diameter threaded backing flange, outer flange and clamp nut must be used for cutting wheels. 1. Install wheel backing flange (R), aligning flats on spindle (Q). 3. Place the wheel on the backing flange, centering the wheel (S) on the backing flange pilot.
17 Accessories BAIL HANDLE This accessor y provides a wider range of holding positions when grinding and is par ticularly useful when sur face grinding concrete. ANTI- VIBRA TION SIDE HANDLE The anti-vibration side handle reduces vibration and user fatigue in extended use applications.
Stanley Black & Decker 82 T ar yn Drive, Epping, VIC 3076 Australia • 1800 338 002 (Aust) or 0800 339 258 (NZ) www .dewalt.com.au • www .dewalt.
デバイスDeWalt DWE4599Nの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
DeWalt DWE4599Nをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDeWalt DWE4599Nの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。DeWalt DWE4599Nの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。DeWalt DWE4599Nで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
DeWalt DWE4599Nを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDeWalt DWE4599Nの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、DeWalt DWE4599Nに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDeWalt DWE4599Nデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。