FireplaceXtrordinairメーカー36A-BIの使用説明書/サービス説明書
ページ先へ移動 of 30
.
Page 2 SAFETY PRECAUTIONS ¥ VIEWING DOOR MUST BE CLOSED AND LATCHED DURING OPERATION. ¥ THIS APPLIANCE HAS BEEN DESIGNED AND TESTED FOR BURNING OF WOOD OR NATURAL GAS ONLY. THE BURNING OF ANY TYPE FUEL OTHER THAN WOOD OR NATURAL GAS WILL VOID THE WARRANTIES AND SAFETY LISTINGS OF THE APPLIANCE.
Page 3 TABLE OF CONTENTS Page IMPORTANT INFORMATION Introduction ............................................................................................................................... ....... 1 Safety Precautions .............................
Page 4 FEATURES AND SPECIFICATIONS ¥ EPA Phase II approved. ¥ Heavy duty steel construction. ¥ Thermostat for automatic control of the blower. ¥ Large firebox capacity - 3 cu. ft. ¥ Long burn time - 10 Hours. ¥ Large glass doors for maximum visibility.
Page 5 CHIMNEY SIZE AND PROPER DRAFT Your Fireplace Xtrordinair comes with a set of installation instructions. These instructions should be followed by the installer and kept for future reference. Before installing the fireplace the chimney's size and draft should be verified.
Page 6 PROTECTING T HE G OL D O N T HE F IREPL A CE X TRORDINA IR Gold is the very best material available for plating fireplace fronts, but it is not indestructible. The most common complaint with any plated surface on a wood burning appliance is discoloration.
Page 7 OPERATING YOUR APPLIANCE Location and Use of Controls NOTE: The Combustion Air Control and Combustor By-Pass Control become hot during operation.
Page 8 OPERATING YOUR APPLIANCE (Continued) To build a fire in disregard of the information provided in this section can cause permanent damage to your appliance and void your warranty. This appliance is not designed for use with the door open. Burning with the loading door open could create a safety hazard.
Page 9 OPERATING YOUR APPLIANCE (Continued) Maintaining Catalytic Light-Off Your Fireplace Xtrordinair is equipped with a catalytic combustor which increases the efficiency of your appliance. It is located along the roof of the firebox and is accessed from within.
Page 10 OPERATING YOUR APPLIANCE (Continued) Burning Your Appliance Efficiently Your Fireplace Xtrordinair is designed to heat your home efficiently with the lowest amount of creosote build-up and pollutants emitted.
Page 11 OPERATING YOUR APPLIANCE (Continued) Wood This appliance is designed to burn natural wood only. Higher efficiencies and lower emissions generally result when you burn air dried, seasoned hardwoods as compared to softwoods or to green or freshly cut hardwoods.
Page 12 OPERATING YOUR APPLIANCE (Continued) Wood (Continued) Wet wood not only causes more work for you due to the increase in weight making it more burdensome to carry, but most importantly it will not burn as efficiently.
Page 13 OPERATING YOUR APPLIANCE (Continued) Seasoning Wood (Continued) Place firewood in an open area to obtain rapid drying and to prevent deterioration. Preferably, put a cover on the top tier of wood. If you cut trees in summer, let them lie for a week.
Page 14 OPERATING YOUR APPLIANCE (Continued) Seasoning Wood (Continued) The bathroom scales can be used to check if firewood is still seasoning. Weigh a basket or bag of a few pieces of firewood. Place them back in the wood pile as an identified unit.
Page 15 OPERATING YOUR APPLIANCE (Continued) Storing Wood (Continued) If sufficient space is available under a roof, seasoning and storage can be accomplished in one handling. This practice eliminates the extra handling of moving wood that has been dried outside into a covered storage area.
Page 16 OPERATING YOUR APPLIANCE (Continued) SAFETY IN OPERATION The Following Safety Rules Should Be Followed Whenever Using Your Appliance: 1 . Do not use this appliance for any purpose other than heating.
Page 17 CARE AND MAINTENANCE Maintenance Schedule The following schedule should be followed to insure your appliance stays in peak condition. Weekly Maintenance: The following should be done once a we.
Page 18 CARE AND MAINTENANCE (Continued) GLASS CLEANING Clean the glass only when the appliance is cool, using a non-abrasive cleaner. If the glass cracks or breaks, let the appliance cool before replacing it. DO NOT OPERATE THE APPLIANCE WITH BROKEN OR MISSING GLASS.
Page 19 CARE AND MAINTENANCE (Continued) If the door is too loose (it has more than 1/16" of play), the latch needs to be adjusted closer to the door (tightened). To do this, first remove the outer nut, the washer next to it, the latch, the inner nut, and the two washers next to the inner nut.
Page 20 CARE AND MAINTENANCE (Continued) CHECK FOR CREOSOTE (Continued) Most problems with creosote are due to poor chimneys with low draft and/or cold chimney walls, and to a low rate of burn when little heat is needed during the spring and fall months.
Page 21 CARE AND MAINTENANCE (Continued) CATALYTIC COMBUSTOR INSPECTION & CLEANING (Continued) mode). Use the following three steps to determine your catalytic combustor's performance: Step 1. Light fireplace. Let the fireplace reach operating temperature.
Page 22 CARE AND MAINTENANCE (Continued) CHIMNEY SYSTEM CLEANING We recommend you have your chimney system and appliance checked and cleaned by a competent chimney sweep at least once a year. The chimney should be fully sealed and securely attached. The chimney termination should be free of all blockage (ash, leaves, etc.
Page 23 BEFORE CALLING FOR SERVICE SAVE TIME AND MONEY - CHECK THIS LIST BEFORE YOU CALL FOR SERVICE To eliminate unnecessary service calls, first read all the instructions in this manual carefully.
Page 24 REPLACEMENT PARTS AND REMOVAL INSTRUCTIONS Several components inside your appliance are serviceable by you. These components are usually easy to remove and replace without special tools. Before you attempt to carry out any of these steps, be sure to read through the entire section.
Page 25 REPLACEMENT PARTS AND REMOVAL INSTRUCTIONS (Continued) Removing and Replacing the Glass DO NOT OPERATE THE APPLIANCE WITH BROKEN OR MISSING GLASS. IF THE GLASS DOES BREAK, FOLLOW THE DIRECTIONS BELOW TO REPLACE THE GLASS. To remove the glass, simply remove the fiberglass packing rope that holds the window in place.
Page 26 REPLACEMENT PARTS AND REMOVAL INSTRUCTIONS (Continued) Removing and Replacing the Firebricks The firebricks inside your wood-burning appliance are used to store the radiating heat and create a more thorough combustion inside the firebox. Occasionally one of them will crack and require replacement.
Page 27 REPLACEMENT PARTS AND REMOVAL INSTRUCTIONS (Continued) Removing and Replacing the Firebricks (Continued) REMOVING THE BOTTOM FIREBRICKS (Continued) 4. Remove the bottom firebricks in the order listed below. Note the position of each firebrick as they are being removed from the firebox.
Page 28 REPLACEMENT PARTS AND REMOVAL INSTRUCTIONS (Continued) Removing and Replacing the Catalytic Combustor (Continued) 2. Reach into the firebox and remove the baffle that is along the roof of the firebox right behind the doors by sliding it backwards and then pivoting it down.
Page 29 5-YEAR WARRANTY TRAVIS INDUSTRIES, INC. warrants the FIREPLACE XTRORDINAIR appliance to be defect-free in material and workmanship for five (5) years from the date of purchase, with the exception of the glass, gold plating, paint, brick, refractory, removable baffle parts and blowers.
Page 30 SAFETY LABEL 36A-BI 36A-ZC.
デバイスFireplaceXtrordinair 36A-BIの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
FireplaceXtrordinair 36A-BIをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFireplaceXtrordinair 36A-BIの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。FireplaceXtrordinair 36A-BIの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。FireplaceXtrordinair 36A-BIで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
FireplaceXtrordinair 36A-BIを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFireplaceXtrordinair 36A-BIの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、FireplaceXtrordinair 36A-BIに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFireplaceXtrordinair 36A-BIデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
