FireplaceXtrordinairメーカー564の使用説明書/サービス説明書
ページ先へ移動 of 30
564 SS IPI Fireplace • Operation • Maintenance Tested and Listed by OMNI-Test Laboratories, Inc. Beaverton, Oregon Report # 028-F-80b-5 ANSI Z21.88a-2003 WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
2 Introduction © Travis Industries 4081205 100-01211_000 Introduction We welcome you as a new owner of a 564 SS gas fireplace. This manual details operation and maintenance of this fireplace. Please familiarize y ourself with the Owner's Manual before operating your heater and save the manual for future reference.
Introduction 3 © Travis Industries 4081205 100-01211_000 Table of Contents Introduction and Important Information Introducti on ......................................................................... 2 Important In formati on ......................
4 Safety Precautions © Travis Industries 4081205 100-01211_000 IF YOU SMELL GAS: * Do not light any appliance * Extinguish any open flame * Do not touch any electrical switch or plug or unplug anythi.
Safety Precautions 5 © Travis Industries 4081205 100-01211_000 Do not place clothing or other flammable items on or near the heater. Because this heater can be controlled by a thermostat there is a possibility of the heater turning on and igniting any items placed on or near it.
6 Operation © Travis Industries 4081205 100-01211_000 Before You Begin • Read this entire manual before you use your new fireplace (especially the section "Safety Precautions" on pages 4 & 5). Failure to follow the instructions may result in property damage, bodily injury, or even death.
Operation 7 © Travis Industries 4081205 100-01211_000 Starting the Fireplace for the First Time • Burn the heater at a high setting with the blower off for an extended period (up to 48 hours). This will cure the painted surfaces. Fumes from the paint curing and oil burning off the steel will occur.
8 Operation © Travis Industries 4081205 100-01211_000 Adjusting the Flame Height This fireplace has an adjustable flame to tailor the look and heat output to your specific needs.
Operation 9 © Travis Industries 4081205 100-01211_000 Adjusting the Optional Blower Speed The blower helps transfer heat from the heater into t he room. It will not turn on until the heater is up to temperature (approximately 15 minutes after starting).
10 Operation © Travis Industries 4081205 100-01211_000 Normal Operating Sounds Gas Control Valve As the gas control valve is turned on and off you will hear a dull clicking sound. This is the valve opening up and shutting down. Blower Snap Disk This part can produce a clicking sound as it turns the blower on and off.
Maintenance 11 © Travis Industries 4081205 100-01211_000 Maintaining Your Fireplace's Appearance Fingerprints or other marks left on the optional plated surface may become etched in place if they are not wiped clean prior to turning the fireplace on.
12 Maintenance © Travis Industries 4081205 100-01211_000 Accent Light Replacement Two accent lights are included in your fireplace to provide additional lighting. These bulbs will burn out over time. To replace, follow the directions below: • Shut off gas to the fireplace and let it cool for 15 minutes.
Maintenance 13 © Travis Industries 4081205 100-01211_000 Grill Installation and Removal Follow the directions below to install. Upper Grill Installation (FPX and Avalon) Hold the grill at an angle and insert the lower slot over the lower bushing on the fireplace (both sides) Swing the grill upwards to engage the upper slot.
14 Maintenance © Travis Industries 4081205 100-01211_000 Face Installation and Removal Some fireplaces have a face that fits over the glass frame. The face can be removed following the directions below. Phillips Screwdriver Four screws hold the face in place.
Maintenance 15 © Travis Industries 4081205 100-01211_000 Glass Frame Removal and Installation Warning: The appliance must be completely cool before removing the glass.
16 Maintenance © Travis Industries 4081205 100-01211_000 Glass Frame Removal and Installation (continued) The latch can come loose from the latch assembly. This occurs only when it is rotated. Follow the directions below to re-install the latch if it comes loose.
Maintenance 17 © Travis Industries 4081205 100-01211_000 Log Set Installation Log Set Overview When installed, the logs should appear as shown below. Rear Lo g Ri g ht Twi g Left Lo g Left Twi g Ri g.
18 Maintenance © Travis Industries 4081205 100-01211_000 Rear Log Installation The rear log has a flat notch on both sides that center it on the grate. Place the rear log on the grate and slide it all the way back until the log contacts the end- brackets on the grate.
Maintenance 19 © Travis Industries 4081205 100-01211_000 Right Log Installation The left log has a groove that fits over the grate. Note how the left side of the log rests on the burner but does not cover any burner holes.
20 Maintenance © Travis Industries 4081205 100-01211_000 Left Log Installation The left log has a groove that fits over the grate. Note how the right side of the log rests on the burner but does not cover any burner holes.
Maintenance 21 © Travis Industries 4081205 100-01211_000 Left Twig Installation The left twig should be positioned so the front edge contacts the grate as shown above.
22 Maintenance © Travis Industries 4081205 100-01211_000 Right Twig Installation The right twig has two holes for the pins on the rear and right log. When in place the right twig will a pp ear as shown above.
Maintenance 23 © Travis Industries 4081205 100-01211_000 Ember Installation A bag of embers is provided to further enhance the firebox. Place the embers on the firebox floor and on the burner. Do not place embers over any of the burner holes or air channels.
24 Maintenance © Travis Industries 4081205 100-01211_000 Glass Cleaning The glass may be cleaned with a non- abrasive cleaner. To clean the inside of the glass, simply remove the glass frame, place it on a non-scratching surfac e, and clean the inside surface.
Maintenance 25 © Travis Industries 4081205 100-01211_000 Troubleshooting Table Problem: Possible Cause: Don't Call for Service Until You: Main Burners Will Not Start The ON/OFF switch is turned .
26 Maintenance © Travis Industries 4081205 100-01211_000 Wiring Diagram CN4 CN3 PILOT SENSOR SP ARK ROD DIGIT AL FIREPLACE BURNER CONTROL CN2 GROUND VAL VE COMMAND POWER CN1 DIAGNOSTIC CN0 COMFORT CO.
Limited 7 Year Warranty 27 © Travis Industries 4081205 100-01211_000 Register your TRAVIS INDUSTRIES, INC. Limited 7 Year W arranty online at traviswarranty.com , or complete the enclosed Warranty card and mail it within ten (10) days of the appliance purchase date to: TRAVI S I NDUSTRI ES, INC.
28 Optional Equipment © Travis Industries 4081205 100-01211_000 Accessories The accessories listed below are available at y our Travis dealer. To locate a dealer, visit: www.travisproducts.com GreenSmart™ Remote / Thermostat This accessory allows for remote control of your fireplace (burner, flame heigh t, ac cent light).
Optional Equipment 29 © Travis Industries 4081205 100-01211_000.
30 Index © Travis Industries 4081205 100-01211_000 Index Accent Light R eplacement .................................................. 12 Accent Li ght ........................................................................ 8 Adjusting the Fl ame Hei ght .
デバイスFireplaceXtrordinair 564の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
FireplaceXtrordinair 564をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFireplaceXtrordinair 564の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。FireplaceXtrordinair 564の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。FireplaceXtrordinair 564で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
FireplaceXtrordinair 564を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFireplaceXtrordinair 564の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、FireplaceXtrordinair 564に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFireplaceXtrordinair 564デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。