Heat & Glo LifeStyleメーカーTWILIGHT-IIの使用説明書/サービス説明書
ページ先へ移動 of 37
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 1 Model: T wilight-II* Owner ’ s Manual Installation and Operation * Does not ship with interior or exterior door , or TL-Trim kit. These items must be purchased separately.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 2 Congratulations Listing Label Information/Location Model Name: ___________________________________________ Date p.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 3 - T able of Contents - Section 8: Finishing A . Mantel Projections ................................... 1 8 B . Facing Material .....................................
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 4 B. Glass Specifications Hearth & Home T echnologies appliances manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the Consumer Product Safety Commission (CPSC).
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 5 A. Design and Installation Considerations Heat & Glo direct vent gas appliances are designed to op- erate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 6 3 Framing and Clearances NOTE: • Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONL Y. • I llustrations/diagrams are not drawn to scale.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 7 B. Clearances Figure 3.3 Clearances to Combustibles Fire Risk. • Locate and install appliance to all clearance specifications in manual W ARNING Fire Risk. Odor Risk.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 8 C. Mantel Projections - Interior only Figure 3.4 Indoor Clearances to Mantels or other Combustibles above Appliance Figure 3.5 Indoor clearances to Mantel Legs or Wall Projections (Acceptable on both sides of opening.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 9 T ermination Locations 4 ___________________________________________________________________________ ____________.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 10 The diagram shows how to properly position, level, and se- cure the appliance (see Figure 5. 2). Nailing tabs are provid- ed to secure the appliance to the framing members.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 11 • See Figure 5.3 for placement of combustible housewrap or building paper and non-combustible sheathing for the outside wall.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 12 NOTE: Have the gas supply line installed in accordance with local building codes, if any . If not, follow ANSI 223.1. Installation should be done by a qualified installer approved and/or licensed as required by the locality .
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 13 W ARNING Fire hazard. Do NOT change the valve settings. • This valve has been preset at the factory . • Changing valve settings may result in fire hazard or bodily injury .
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 14 A. Recommendation for Wire This appliance requires 1 10-120 V AC be wired to the junction box for proper operation of the appliance.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 15 Wall Switch Position the wall switch in the desired position on a wall. Run a maximum of 25 feet (7.8 m) or less length of 18 A.W .G . minimum wire and connect it to the appliance ON/ OFF switch pigtails.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 16 Figure 7.3 Intellifire Pilot Ignition (IPI) Wiring Diagram * NOTE: 1. Ignition module, valve, pilot, and wall switch operate on 3 volts. Uninterrupted 120 V AC is required at junction box unless equipped with battery back-up.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 17 E. Junction Box Installation F . W all Switch Inst allation for Fan (Optional) If the box is being wired from the OUTSIDE of the appliance: • Install the Romex ™ connector (not included with appliance) in the side wrap.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 18 A. Mantel Projections Figure 8.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 19 Outside Facing Material Fire Risk. Finish all edges and fronts to clearances and specifications listed in manual. W ARNING • Black metal columns may be covered with non- combustible material only .
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 20 Figure 8.5 Exterior View APPLIANCE HOOD TOP OF APPLI ANCE SOFF I T SIDING HOUSE W R AP (BUILD ING P A PE R) A ND.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 21 Appliance Setup 9 A. Remove Shipping Materials Remove shipping materials from inside or underneath the firebox. B. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity .
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 22 E. Positioning the Logs Log Set Assembly: LOGS-TWI 1 2 2005-937D CAUTION: Logs are fragile! Carefully remove the logs from the packaging. Remove the metal supports which held the log box in place during shipping.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 23 STEP 4. LOG #3 (SRV2005-702): Position log #3 as shown by leaning it against log # 2 and resting the other end on the peak of the burner . Do not cover any port holes.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 24 STEP 8. LOG #7 (SRV703-703): Place log #7 on the grate tine between log #2 and log #5. Rest one end on the burner making sure not to cover any port holes. STEP 7. LOG #6 (SRV2077-701): Set log #6 onto the grate bar as shown.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 25 A. Before Lighting Appliance Operating Instructions 10 CAUTION If installing Intellifire ignition battery backup: • Do not install batteries if the backup mode may not be used for extended time.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 26 B. Lighting Appliance Intellifire Ignition Final Inspection by _________________________________ 1. Turn off all electric power to the appli- ance. 2. This appliance is equipped with an ig- nition device which automatically lights the burner .
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 27 C. Af ter Appliance is Lit D. Frequently Asked Questions Initial Break-in Procedure When you light the appliance, you may notice that it pro- duces heat which does have an associated odor or smell.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 28 T roubleshooting 11 With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 29 Intellifire Ignition System - (continued) Sym pt om P ossibl e C auses Correct i ve Act i on s 3. C on t i n u ed d. Damaged pilot assem bl y or dirt y sen sor r od.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 30 Maint aining and Servicing Appliance 12 Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualified service technician should perform an appliance check-up at the beginning of each heating season.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 31 I nspect Mai nt en ance T asks Doors, Su r rou n ds an d Fr on t s 1. Assess c on di t i on of scr een an d r epl ace as n ecess ary . R ecom mend addi t i on of scr een i f on e i s not present .
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 32 Reference Materials 13 Locati on In ch e s Millime te r Locati on In ch e s Millime te r A 4-3/ 4 121 J 36-1/ 4 .
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 33 Part number list on following page. (NG , LP) Exploded Parts Diagram B.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 34 B. Service Parts List See following page for additional IPI service part numbers.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 35 14 (NG , LP) Exploded Parts Diagram Service Parts TWILIGHT -II Beginning Manufacturing Date: 6-05 Ending Manufac.
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 36 © 2005 Hearth & Home T echnologies Inc. C. Limited Lifetime W arranty LIMITED LIFETIME W ARRANTY HEA T & GLO GAS APPLIANCE PRODUCTS BASIC ONE-YEAR W ARRANTY .
Heat & Glo LifeS tyle Collection • T wilight-II • 2087-900 Rev . G • 12/05 37 Heat & Glo LifeS tyle Collection, a brand of Hearth & Home T echnologies Inc.
デバイスHeat & Glo LifeStyle TWILIGHT-IIの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Heat & Glo LifeStyle TWILIGHT-IIをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHeat & Glo LifeStyle TWILIGHT-IIの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Heat & Glo LifeStyle TWILIGHT-IIの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Heat & Glo LifeStyle TWILIGHT-IIで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Heat & Glo LifeStyle TWILIGHT-IIを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHeat & Glo LifeStyle TWILIGHT-IIの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Heat & Glo LifeStyle TWILIGHT-IIに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHeat & Glo LifeStyle TWILIGHT-IIデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
