HitachiメーカーG13VAの使用説明書/サービス説明書
ページ先へ移動 of 12
Electronic Disc Grinder Model G 12V A • G 13V A • G 13YF Handling instructions Note: Before using this Electric Power Tool, carefully read through these HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is recommended that these INSTRUCTIONS be kept readily available as an important reference when using this power tool.
1 GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
2 PRECAUTION Keep children and infirm persons away. When not in use, tools should be stored out of reach of children and infirm persons. SAFETY WARNINGS COMMON FOR GRINDING, SANDING OR ABRASIVE CUTTING-OFF OPERATIONS a) This power tool is intended to function as a grinder, sander or cut-off tool.
3 c) Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite to the wheel’s movement at the point of snagging. d) Use special care when working corners, sharp edges etc.
4 SPECIFICATIONS * Be sure to check the nameplate on product as it is subject to change by areas. Electronic Control The grinder has an electronic speed control which provides: 䡬 full speed at all times in the range up to rated load. 䡬 soft-start.
5 4. Fitting and adjusting the wheel guard The wheel guard is a protective device to prevent injury should the depressed center wheel be shattered during operation. Ensure that the wheel guard is properly fitted and fastened before commencing grinding operation.
6 CAUTION When using the tool at any value except the full speed (Dial scale 6), the motor cannot be sufficiently cooled due to the decreased number of revolution. This could result in the risk of burning and damaging the motor before an overload protective mechanism starts to function.
7 MAINTENANCE AND INSPECTION 1. Inspecting the depressed center wheel Ensure that the depressed center wheel is free of cracks and surface defects. 2. Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened.
8 5. Replacing supply cord If the replacement of the supply cord is necessary, this has to be done by the manufacturer of this agent in order to avoid a safety hazard. 6. Maintenance of the motor The motor unit winding is the very “heart” of the power tool.
9 G1 2V A / G1 3V A ITEM NO. PART NAME Q’TY 1 SEAL LOCK SCREW 2 (W/SP. WASHER) M4 × 10 2 TAPPING SCREW D5 × 25 4 3 PUSHING BUTTON 1 4 GEAR COVER ASS'Y 1 5 NUT M6 1 6 SEAL RING (A) 1 7 WASHER (C) 1 8 BALL BEARING 629T12DDC3PS2-L 1 9 RUBBER RING 1 10 BEARING COVER 1 11 ARMATURE 1 12 FAN GUIDE 1 13 HEX.
10 502 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 20 21 22 23 24 25 26 27 28 29 31 32 33 35 36 37 34 39 46 47 38 40 41 42 48 49 53 58 59 52 55 56 61 57 62 63 19 60 54 50 41 45 43 40 44 30 51 52 503 64 501 G1 3YF ITEM NO. PART NAME Q’TY 1 SEAL LOCK SCREW 2 (W/SP.
102 Code No. C99179313 M Printed in Malaysia Hitachi Koki Co., Ltd. Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan 02Back_G12VA_Eng 1/12/11, 4:43 PM 11.
デバイスHitachi G13VAの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Hitachi G13VAをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHitachi G13VAの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hitachi G13VAの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hitachi G13VAで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hitachi G13VAを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHitachi G13VAの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hitachi G13VAに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHitachi G13VAデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。