HoshizakiメーカーC-100BAFの使用説明書/サービス説明書
ページ先へ移動 of 34
Hoshizaki “A Superior Degr ee of Reliability” www .hoshizaki.com Models C-100BAF C-100BAF-DS C-100BAF-AD C-100BAF-ADDS Self-Contained Cubelet Hoshizaki America, Inc.
2 IMPOR T ANT Only quali ed ser vice t echnicians should install, service, and maintain the icemaker . No installation, ser vice , or maintenance should be under tak en until the technician has thor oughly r ead this Instruction Manual.
3 IMPOR T ANT This manual should be r ead car efull y bef ore the icemak er is installed and operat ed. Only quali ed ser vice technicians should inst all, ser vice , and maintain the icemak er . Read the warnings contained in this booklet car efull y as they giv e impor tant inf or mation reg arding saf et y .
4 Impor tant Saf ety Inf or mation Throughout this man ual, notices appear t o bring your at tention t o situations which could result in death, serious injur y , or damage to the unit. W ARNING Indicates a hazar dous situation which could r esult in death or serious injury .
5 I. Specications A. Construction T op P anel Ice Discharge Opening Scoop Holder F ront P anel P ower S witch Louv er Bin Contr ol Thermostat Bulb Slope Magnet Catch Door P ower C ord.
6 MOTOR-COMPRESSOR THERMALL Y PROTECTED APPROVED FOR OUTDOOR USE Hoshizaki America, Inc. Peachtree City , GA www .hoshizaki.com ICE MAKER 946Z 3152258 CONFORMS TO ANSI/NSF 12 B. Nameplate Rating HOSHIZAKI ICE MAKER MODEL NUMBER C-100BAF SERIAL NUMBER AC SUPPLY VOLTAGE 115-120/60/1 AMPERES 4.
7 C. Dimensions/Connections 1 . C-1 0 0BAF Units: mm [in.].
8 2. C-1 0 0BAF -DS Units: mm [in.].
9 Units: mm [in.] 3. C-1 0 0BAF -AD.
10 4. C-1 0 0BAF -ADDS Units: mm [in.].
11 II. Installation and Operating Instr uctions W ARNING 1 . This icemaker m ust be installed in accor dance with applicable national, stat e , and local codes and regulations . 2 . CHOKING HAZARD: Ensure all components, f astener s, and thumbscre ws are secur ely in place af ter inst allation.
12 2. Built-In Installation Site C A UTION 1 . Do not let the weight of the count er r est on the icemak er . 2. Do not install the icemak er in a cor ner where the door will int erfer e with other equipment or where the icemak er cannot be pulled out for service.
13 C. Door 1 . C-1 0 0BAF , C-1 0 0B AF-AD a) Hinge R ev er sal If you w ould lik e t o r e ver se the door hinges , f ollow the steps belo w . Otherwise, skip t o section"II.D . Setup ." 1) W hile maintaining a hold on the door , remo v e the hinge st op pin fr om hinge (B).
14 4) Remo ve hinge (B) fr om the right side of the unit and the 2 ller scr e ws fr om the lef t side. At tach the 2 ller scr e ws t o the right side and at tach hinge (B) t o the lef t side. See F ig . 4. 5) Rot at e the t op panel 1 80° from its pr evious position.
15 1 2 3 4 6 5 2. C-1 0 0BAF -DS, C-1 0 0B AF-ADDS a) Over lay P anel F abr ication and Attac hment IMPOR T ANT The ov er la y panel must be craf ted b y a prof essional cabinet maker t o ensur e quality results. (1) P arts Ensure that all parts required f or the ov er la y panel assembl y ar e contained in the accessories bag.
16 (2) Over lay P anel Specication Use the specication that applies to y our icemaker (C-1 00BAF -DS or C-1 00BAF -ADDS ) and the directions that f ollow t o prepare y our ov erla y panel.
17 C-1 0 0B AF-ADDS Ov erla y P anel Specication Ov erlay P anel Height 279/1 6"(700mm) Ov erlay P anel W idth 1 41 3/1 6"(37 6mm) Ov erlay P anel Thickness 5/8"(1 6mm)minimum; 3/4"(1 9mm)maximum Ov erlay P anel and Door W eight (t otal) 20 lb .
18 3)Scre wthe6threadedwoodinser tsint othe1/4"holesdr illedinthepr e viousstep . Make sure that the inserts are threaded str aight and that the t ops of the inser ts ar e ush t o the ov er la y panel surface .
19 Scre ws T op P anel f) Remo ve hinge (C1) fr om the t op right par t of the door , ip it and r eat tach to the bot tom lef t. R emov e hinge (C2) from the bot tom right par t of the door , ip it and reat tach t o the top lef t. See F ig . 1 5.
20 9) T emporar il y fast en the ov erlay panel t o the door using 2 of the M4×25 pan head scre ws pro vided. See Fig . 1 8. C A UTION Ensure that the bac k surface of o verlay panel is at bef or e at taching . 1 0) Mark the center point of the hinge (C1) and hinge (C2) holes that e xtend o v er the ov er la y panel.
21 Snug the scr ews , but do not tight en. Sheet Metal Brac ket Ov erlay P anel Tight en the screws . 5) F asten the o verlay panel t o the door using the four M4×25 pan head scr ews pr ovided. Snug the screws , but do not tight en. See F ig . 24. 6) F asten the sheet met al brac ket t o the bot tom of the door with the thr ee T2 screws pro vided.
22 7) Tight en the four M4×25 pan head scr ews installed in st ep 5. See Fig . 26. 8) Replace the door g asket in its pr oper orientation. Reinser t the bushings int o hinge (C1) and hinge (C2) (the hinges at tached to the door). See F ig. 27 . C anoe Clips F ig.
23 D . Set up 1) P osition the icemaker in the select ed per manent location. 2) Le v el the icemaker fr om side-to-side and fr ont-to-r ear b y adjusting the f eet. E. Electrical Connection W ARNING 1 . Electrical connection must meet national, stat e, and local electrical code requir ements.
24 F . W ater Suppl y and Dr ain Connections W ARNING 1 . W at er suppl y and drain connections must be inst alled in accor dance with applicable national, st at e , and local r egulations. 2. Normal operating wat er t emperatur e should be within 45°F to 90°F (7°C to 32°C).
25 G. F inal Chec klist W ARNING CHOKING HAZARD: Ensure all components , fast eners, and thumbscr ews ar e securel y in place af t er installation. Make sur e that none hav e f allen into the stor age bin.
26 H. Star t up W ARNING 1 . All par ts are f actory -adjusted. Improper adjustments ma y adv er sely af fect saf ety , performance, component lif e, and warranty cov erage. 2. If the icemak er is turned of f , w ait f or at least 3 minutes bef ore r estar ting the icemaker t o pre vent damage t o the compr essor .
27 III. Cleaning and Maintenance This icemaker m ust be cleaned and maintained in accor dance with the instr uction manual and labels pr o vided with the icemak er . C onsult with y our local distribut or about cleaning and maintenance service. T o obtain the name and phone number of your local distrib ut or , visit www .
28 3) W hile maintaining a hold on the door , remo v e the hinge st op pin fr om hinge (B). P ull out the bot tom of the door slightl y , then gently r emov e the door fr om hinge (A). See Fig . 31 . 4) Remo ve the 2 scr e ws securing the top panel, then lif t it of f.
29 1 2) Allow the icemaker t o sit for 1 0 minut es bef or e operation. If you placed a clamp on the reservoir hose in st ep 1 1, remo v e it bef ore operation and r eplace the spout in its correct position. 1 3)Plugtheunitbackin. Mov ethepow ers witchtothe"ON"position.
30 5. Sanitizing Pr ocedur e - F inal 1) Remo ve the drain plug t o drain any r emaining solution. 2) Af ter all of the solution has drained, r eplace the drain plug in its correct position. 3) Remo ve the r eser v oir cov er . P our the sanitizing solution into the r eser v oir until the solution star ts t o ow thr ough the ov ero w hose.
31 B. Maintenance The maintenance schedule belo w is a guideline. Mor e fr equent maint enance ma y be requir ed depending on wat er quality , the icemaker's en vironment, and local sanitation regulations . W ARNING 1 . Only quali ed ser vice t echnicians should at tempt t o service this icemaker .
32 1 . St or age Bin Dr ain In some conditions, slime ma y build up inside the st orage bin drain and pre v ent wat er from dr aining pr operly . T o pre vent this b uildup, perf or m the f ollowing pr ocedur e once e v er y 3 months or as of ten as necessar y f or conditions.
33 C. Pr eparing the Icemak er f or Long Stor age C A UTION When st or ing the icemak er for an e xtended time or in sub-fr eezing temper atur es , f ollow the instructions below to pr ev ent damage.
34 HOSHIZAKI AMERICA, INC. 618 Hwy . 74 S., Peachtree Cit y, GA 30269 USA TEL (770) 487-2331 F AX (770) 487-3360 www.hoshizaki.com 91A2UC10D.
デバイスHoshizaki C-100BAFの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Hoshizaki C-100BAFをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHoshizaki C-100BAFの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hoshizaki C-100BAFの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hoshizaki C-100BAFで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hoshizaki C-100BAFを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHoshizaki C-100BAFの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hoshizaki C-100BAFに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHoshizaki C-100BAFデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。