Huffyメーカー600の使用説明書/サービス説明書
ページ先へ移動 of 26
1 02/05 P/N 211636 10 © COPYRIGHT 2005 by HUFFY SPORTS Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339 , For Europe: 00 800 555 85234 (Sweden: 009 555 85234 ), For Australia: 1-800-333 061 Internet Address: http://www.
2 P/N 211636 10 02/05 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator component s and hardware is required. T est-fit large bolt s into large holes of elevator tubes, backboard bracket s, and triangle plates.
02/05 P/N 211636 10 3 W ARNING F AILURE T O FOLLOW THESE W ARNINGS MA Y RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NO T HANG on the rim or an y par t of the system including bac kboard, support braces or net.
4 P/N 211636 10 02/05 SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system.
02/05 P/N 211636 10 5 For more information on assembly, placement, proper use, and maintenance, visit The American Basketball Council website at http://www.smarthoops.com. IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p art s are packed inside.
6 P/N 211636 10 02/05 Get to know the basic parts of your basketball system..... FRONT P ANEL BACKBOARD FRONT RIM BASE POLE.
02/05 P/N 211636 10 7 P ARTS LIST - (See Hardware Identifier) Item Qty. Part No. Description 1 1 200503 Cover, Black OR 1 200504 Cover, Red 2 1 806620 Base Assembly 3 1 804833 Exacta Height Assembly 4.
8 P/N 211636 10 02/05 HARDW ARE IDENTIFIER (BOL TS & SCREWS) * You may have extra parts with this model. Item #7 (2) Item #40 (1) Item #39 (2) Item #23 (1) Item #29 (6) Item #16 (2) Item #12 (1) I.
02/05 P/N 211636 10 9 HARDW ARE IDENTIFIER (STEEL SP ACERS) HARDW ARE IDENTIFIER (NUTS & W ASHERS) HARDW ARE IDENTIFIER (PLASTIC SP ACERS CAPS & CLIPS) Item #28 (2) Item #21 (2) Item #13 (2) I.
10 P/N 211636 10 02/05 TOOLS REQUIRED FOR THIS SECTION HARDW ARE USED IN THIS SECTION (not actual size) SECTION A: ASSEMBLE THE BASE And/Or: This is what your system will look like when you’ve finis.
02/05 P/N 211636 10 11 1A. Check the following pre-assembled base areas for tightness: Eye bolt s P/N 203452, W asher P/N 203218 , Nut P/N 203100, Carriage Bolts P/N 203223 .
12 P/N 211636 10 02/05 Check the following pre-assembled handle areas for tightness: Screw P/N 204803, Nut P/N 203100, Carriage Bolt s P/N 203103 . Carriage Bolt P/N 203103 Nut P/N 203100 Nut P/N 2031.
02/05 P/N 211636 10 13 6 5 4 3. WOOD SCRAP (NOT SUPPLIED) 5 4 While maintaining alignment, bounce middle pole section (5) into top section (4) using a wood scrap as shown until the top pole no longer moves toward the pole identification sticker on the middle pole.
14 P/N 211636 10 02/05 4. 4 5 6 WOOD SCRAP (NOT SUPPLIED) RODS SHOWN ARE FOR VISUAL REPRESENTATION OF ALIGNMENT AND ARE NOT SUPPLIED WITH THE HARDWARE TROUGH Align dimple of middle pole section (5) into trough of bottom pole section (6) as shown. IMPORT ANT!: POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP.
02/05 P/N 211636 10 15 9 7 6 9 7 13 8 47 5. Install bolt (12) through bracket and bottom pole section (6) and secure with nut (10) as shown. Nut should be tightened until flush (even) with locknuts outer edge. 12 10 6 7. Secure cover to rod (9) using washers (47) nuts (8) and nut covers (13) as shown.
16 P/N 211636 10 02/05 8 . Install pole mount bracket (15) and reinforcement bracket (49) with carriage bolt s (16) as shown. T ighten flange nuts (14) completely . 4 49 14 14 15 16 16 9. Attach sp acers (20, 21) to pole mount bracket (15) with bolts (19), washers (17), and nuts (18) as shown.
02/05 P/N 211636 10 17 Assemble lanyard (25) to locking pin (24) as shown (FIG A). Attach covers (22) onto pole mount bracket (15) with carriage bolt (23) and nut (14) as shown. 10 . 15 14 24 22 22 25 23 FIG . A 25 24 Loop end of pin lanyard (25) over carriage bolt (23) as it p asses through the pole mount bracket (15) during this assembly .
18 P/N 211636 10 02/05 TOOLS REQUIRED FOR THIS SECTION HARDW ARE USED IN THIS SECTION (not actual size) SECTION B: A TT ACH THE BACKBOARD Phillip s- Head Screwdriver This is what your system will look.
02/05 P/N 211636 10 19 Assemble backboard brackets (27) using sp acers (28), bolts (19), and nut s (18) as shown. 1. 28 28 19 19 18 18 27.
20 P/N 211636 10 02/05 2. 3. Install cover (1) over spring return mechanism as shown. 29 26 26 27 31 Refer T o Instructions Included With Rim Hardware For Rim Assembly . 48 11 47 32 34 1 39 Attach lower elevator tubes (32) and counter balance springs (33) to backboard support brackets (27) using sp acers (26), bolt (29), and nut (31) as shown.
02/05 P/N 211636 10 21 4. Attach upper elevator tubes (35) to backboard support bracket s (27) using spacers (26 & 1 1), bolt (29), and nut (31) as shown.
22 P/N 211636 10 02/05 5. Install net clip s. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. T wist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows.
02/05 P/N 211636 10 23 Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position. Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP NET INST ALLA TION 6.
24 P/N 211636 10 02/05 31 31 40 38 32 4 37 37 29 30 32 30 29 32 29 35 30 31 31 35 30 37 36 36 7. Support pole on sawhorse. Attach backboard assembly to top pole section (4) as shown. Install pole cap (38). Use caution; elevator assembly is heavy . 8. Install upper elevator tubes (35) to triangle plates (37) as shown.
02/05 P/N 211636 10 25 9. Insert bolt (29) through left side upper elevator tube (35), then stretch spring (33) onto bolt (29). Insert bolt (29) through right side upper elevator tube (35) and secure with nut (31). 10. Roll completed assembly to desired position.
26 P/N 211636 10 02/05 1. Apply height adjustment and moving label (46) to front of pole as shown. 2. A. While holding handle, remove pin (24). B. Move elevator up or down to desired height. C. Replace pin (24) full length to lock system at desired height.
デバイスHuffy 600の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Huffy 600をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHuffy 600の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Huffy 600の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Huffy 600で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Huffy 600を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHuffy 600の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Huffy 600に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHuffy 600デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。