Huffyメーカー89225の使用説明書/サービス説明書
ページ先へ移動 of 20
1 P/N 21154401 01/04 IMPORT ANT! T o ensure prompt and correct handling of any problems, or to answer any questions, please contact the Sample and Display T echnician at 1-800-558-5234.
P/N 21154401 01/04 2 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator component s and hardware is required. T est fit large bolts into large holes of elevator tubes, backboard bracket s and triangle plates.
3 P/N 21154401 01/04 IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p art s are packed inside. NOTICE T O ASSEMBLERS AL L Huffy Sport s Basketball Systems, including those used for DISPLA YS, MUST be assembled and ballasted with sand or water according to the instructions.
P/N 21154401 01/04 4 P A R TS LIST (See Hardware Identifier) Item Qty. Part No. Description 1 2 900033 Back Bracket 2 2 203796 T-Bolt, 3/8-16 x 5 3 2 200318 Bracket 4 2 203472 Spring 5 2 201651 Spacer, .50 I.D. x .25 Long 6 2 206303 Washer, 1/4" Flat 7 8* 203113 Bolt, Hex-Flange 5/16-18 x 2.
5 P/N 21154401 01/04 Item #33 (12) Item #30 (4) Item #40 (4) HARDW ARE IDENTIFIER (BOL TS & SCREWS) Item #67 (2) PLASTIC SP ACERS Item #7 (10) Item #4 (2) Item #22 (2) Item #13 (2) Item #27 (5) It.
P/N 21154401 01/04 6 Install display boards in the marked locations. Each mounting location consist s of a mounting pole stub with the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicate direction the board is facing).
7 P/N 21154401 01/04 At corner locations 1, 2, and 3 install the display pole to the mounting pole stub. If required, secure the display pole by sliding the display wedge (12) into position as shown. T o lock the display pole in place, tighten the set screw (13 or 39).
P/N 21154401 01/04 8 8 11 49 16 1. 2. 17 30 24 52 51 49 30 3. 49 8 55 54 54 57 44 57 55 4. 48 8 46 45 26 47 25 Install pole mount bracket (49) with carriage bolts (16) as shown. T ighten flange nuts (8) completely . Attach sp acers (51, 52) to pole mount bracket (49) with bolts (24), washers (30), and nuts (17) as shown.
9 P/N 21154401 01/04 STEEL FRAME A CR YLIC BACKBOARD ASSEMBL Y - Corner Location 1 37 5. 38 38 24 24 17 17 Attach backboard support brackets (37) to the backboard frame using bolts (24), spacers (38), and nuts (17) as shown . 29 29 39 39 59 37 42 Refer T o Instructions Included With Rim Hardware For Rim Assembly .
P/N 21154401 01/04 10 7. 21 21 27 59 37 42 59 Attach upper elevator tubes (21) to backboard support bracket s (37) using spacers (59), bolt (27), and nut (42) as shown. 8. Attach backboard assembly to pole section (1 1). Install pole cap (43). 42 21 43 21 29 29 27 27 USE CAUTION; ELEVATOR ASSEMBLY IS HEAVY.
11 P/N 21154401 01/04 10. 9. Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05m) mark with pin (55). Attach adjustment rod (47) to lower elevator tubes (29) using bolt (27) spacer (59) and nut (42) as shown.
P/N 21154401 01/04 12 3 35 22 4 58 1 2 • Fit rim (58) securely into bracket (1) as shown. • Install reinforcement bracket (3) onto “T” bolt (2) as shown. • Install spring (4) onto “T” bolt (2) as shown. • Install special nut (35) and washer (22) onto “T” bolt (2).
13 P/N 21154401 01/04 44” F AN MOLDED PLASTIC BOARD ASSEMBL Y - Corner Location 2 Correctly identify each pole section. ONL Y THE T OP POLE SECTION (14) IS USED IN THIS ASSEMBL Y . 1. BOTTOM POLE 43” MIDDLE POLE 43” TOP POLE 31” 14 Fit spacer (15) into p awl (19).
P/N 21154401 01/04 14 Assemble elevator tubes (21) to ratchet (28) and backboard brackets (23) using bolt s (20), spacers (5, & 40), and nut s (42) as shown. T ighten completely . 5 . Secure pawl (19) in place with clevis pin (31) and washers (6) as shown.
15 P/N 21154401 01/04 7. Insert “T” bolt (2) through Slam Jam bracket (1) as shown. Secure Slam Jam bracket (1) and backboard bracket (23) assemblies to backboard. Bend upper halves of backboard brackets (23) to line up with holes in backboard and secure with bolts (44 & 7) and nut s (8).
P/N 21154401 01/04 16 20 20 41 9. Attach upper and lower elevator tubes (21) to top pole section (14) using bolt s (20) and nuts (42) as shown. Attach pole cap (41) as shown. 42 21 21 21 21 • Fit rim (58) securely into bracket (1) as shown. • Install reinforcement bracket (3) onto “T” bolt (2) as shown.
17 P/N 21154401 01/04 Correctly identify each pole section. Poles have an identification sticker that will be used as a reference point in the next step. ONL Y THE T OP POLE SECTION (50) IS USED IN THIS ASSEMBL Y . F AN MOLDED PLASTIC BOARD ASSEMBL Y - Corner Location 3.
P/N 21154401 01/04 18 F AN BACKBOARD ASSEMBL Y - Corner Location 4. TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. WARNING Assemble fan backboard as shown below with a standard rim as shown. 33 32 33 8 65 7 33 1.
19 P/N 21154401 01/04 Install net clip s. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. T wist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows.
P/N 21154401 01/04 20 Install net. Insert net into bottom of clip as shown. SIDE VIEW T wist net until it snaps into position. Net must be centered through clip.
デバイスHuffy 89225の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Huffy 89225をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHuffy 89225の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Huffy 89225の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Huffy 89225で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Huffy 89225を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHuffy 89225の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Huffy 89225に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHuffy 89225デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。