Ice-O-MaticメーカーIOD200の使用説明書/サービス説明書
ページ先へ移動 of 13
Mile High Equipment 11100 East 45th Av e Denver, Colorado 80239 Part Number 9081305-01 Print Date 06/02 MODELS-IOD150, IOD200 AND IOD250 ICE ONLY DISPENSERS SERVICE/INSTALLATION MANUAL.
Introduction IOD150,IOD200,IOD250 To the owner or user: This produc t manual is a source of in formation about the installation, start up, cleaning, maint enance and repair o f the product.
Specifications and Limitati ons IOD150, IO D200, IOD250 Limita tion s: Must meet the same limitations as the cuber installed on top o f it: 5 0 ° F. air minimum 100 ° F. ai r ma xi mum Must be installed indoors. Must allow at least 6-inch clearance at the rear a nd both sides when using an air-cooled ice machine.
For Th e Insta ller IOD150, IOD20 0, IOD250 Equipment Description The IOD150, IOD200 and IOD250 are counter top m ounted ice only dispensers. These units are designed to dispense cube ice only and hav e ice storag e capacities o f 150 lb.,220 lb. and 250 lb.
Installation IOD150, IOD200, IOD250 1. Locate the ice dispenser on the counter. Allow vertical clearance above the unit for the removal of the cover and for pouring ice into the hopper. 2. Plan the unit drain. A one-inch (1”) I.D. drain tube is required for draining.
Water Glass Filler Kit IOD150, IOD200, IOD250 Installation I nstructions WARNING: Disconnect power to unit before p roceeding with installation. 1. Prepare the unit as follows: · Remove the lower front panel · Locate faucet-mounting holes in the front panel.
Water Glass Filler Kit (Con’t) IOD150, IO D200, IOD250 Faucet mounting hole locations. IOD150 Dimens ions A 4.0 Inches B 2.5 Inches IOD200 and IOD 250 Dimensio ns A 6.125 Inches B 3.125 Inches The water inlet tubing can be routed either fr om the back or from underneath the dispenser.
Initial Start Up IOD150, IOD20 0, IOD250 1. Sanitize the ice storage system as ins tructed on Page 10 . 2. Fill the hopper with sanitary ice. 3. Plug the unit’s power cord into an electrical outlet and the li ghted sign should come on. 4. Dispense several containers of ice.
Gate Restrictor Plate IOD150, IOD200, IOD250 CAUTION: Disconnect po wer to dispenser and ice mach ine before installing, remov ing or adjusting restrictor. AD J U S T M E N T This plate may be adjusted as shown to reduce or increase t he dispensing rate of ice, especially desirable when using glasses or o ther containers with small openings.
Cleaning and Sanitizing IOD150, I OD200, IOD250 The sink, grill and splash panel area should b e cl eaned daily. The following dispenser ma intenance should be performed at the int ervals indicated: Dail y (Or A s Required) Remove foreign material from vending area drip tray to prevent drain blockage.
Cleaning and Sanitizing IOD150, I OD200, IOD250 MONTHLY AND INITI AL START UP: Sanitize the Ice Storage System. Note: This should be done by qualified personnel.
Troubleshooti ng IOD150, IOD200, IOD250 IMPOR TA NT: only qualified personnel should service internal components or electrical wiring. Should the dispenser fail to operate properly, check that there is power to the unit and that the hopper contains ice.
Wiring Di agram IO D150, I OD200, IOD250 Page 12.
デバイスIce-O-Matic IOD200の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Ice-O-Matic IOD200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIce-O-Matic IOD200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ice-O-Matic IOD200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ice-O-Matic IOD200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ice-O-Matic IOD200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIce-O-Matic IOD200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ice-O-Matic IOD200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIce-O-Matic IOD200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
