Lennox HearthメーカーEBVI30USの使用説明書/サービス説明書
ページ先へ移動 of 20
Report No. 116-F-15-5 CARE AND OPERA TION INSTRUCTIONS B-V ent Gas Fireplace Heater Inserts Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. WHA T TO DO IF YOU SMELL GAS: • Do not light any appliance.
IM POR T AN T S AFE TY AND W AR NI NG I N F OR MA T I ON REA D TH IS MA NU AL IN I TS ENT IR ET Y A ND U NDE R- ST AND THE SE R ULE S TO FO LL OW FO R SAF ET Y . 2 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. W ARNING Do not attempt to alter or modify the construction of the appliance or its components.
3 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Input of millivolt model is variable. The rates are shown in the following table: Thi s mill avo lt appli anc e is design ed to opera te on either natural or propane gas. A millivolt gas control valve with piezo ignition system provides safe, efficient operation.
4 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Test gauge connections are provided on the front of the millivolt gas control valve (identi- fied IN for the inlet and OUT for the manifold side). See Figures 1 & 2 . This appliance must not be connected to a chimney or flue serving a separate solid-fuel appliance.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 5 CAUTION Wear gloves and safety glasses for protection while doing required maintenance . IMPOR T ANT Always verify proper operation after servicing. W ARNING T urn off gas and electrical power before servicing the appliance.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 6 Small Area Paint T ouch-up The finish of the insert body and surround (optional) is a high-quality powdercoat.
7 Maintenance T ask Accomplishing Person Procedure Inspecting/Cleaning Burner , Logs and Controls Qualified Service T echnician Inspect valve and ensure it is properly operating. Check piping for leaks. Vacuum the control compartment, fireplace logs and burner area.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 8 PROCEDURE FOR REMOVING ST ANDARD GLASS DOOR ASSEMBL Y Burner Flame Appearance BURNER ADJUSTMENT Flame Appearance and Sooting Proper flame appearance is a flame which is blue at the base and becomes yellow/orange in the top of the flame.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 9 If the burner flame appearance differs greatly from what is shown in Figure 13 (see Burner Flame Appearance) , some adjustment from the factory.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 10 1. Place the rear log onto the two corresponding locating pins at the back of the firebox as shown in Figure 16 . 2 . Place the Front Right Log onto the two corresponding locating pins as shown in Figure 17 .
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 11 8. P la ce t he g lo wi ng e mb er s o n th e bu rn er a s sh ow n in F ig u re 2 3 . One package of ember material has been included with this log set Y ou will not need to use the entire bag.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 12 T o light the burner , rotate the gas valve control knob counterclockwise to the “ON” position then turn “ON” the off/on switch mounted.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Figure 28 I f o r i g i n al w i re a s su p p li e d mu s t be r e pl a c e d , i t m u s t be r e pl a c ed w it h T y p e A W M 10 5 ° C, 1 8 g a u ge w ir e .
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 14 Ca t. No . Mo de l Des cr i pt i on H1503 SKS-25 Beveled Surround, Small, EBVI25 H1504 SKM-25 B e ve le d S u rr ou n d, Me d iu m, EBVI25 H088.
15 H I L O W TPTH TP TH P I L O T P I L O T O N it O F F OUT IN 6. Wait five (5) minutes to clear out any gas. If you then smell gas, STOP! Follow “B” in the safety information above on this page. If you do not smell gas, go to the next step. 7. Push in gas control knob slightly and turn counterclockwise to “PILOT .
16 INSTRUCTIONS D’ALLUMAGE – V ANNE GAZ MILLIVOL T INSTRUCTIONS D'ALLUMAGE 8. Enfoncez le bouton de réglage jusqu’au fond et gardez-le enfoncé. Allumez immédiatement la veilleuse en déclenchant l’allume-gaz à étincelle (en poussant le bouton) jusqu’à ce que la veilleuse s’enflamme.
17 REPLACEMENT P AR TS LIST Gas Controls Item # Part/Cat. No. Description Where Used 1 67L70 Pilot Assembly , NG/LP EBVI25 & EBVI30 2 67L68 Pilot T ube EBVI25 & EBVI30 3 67L67 Thermocouple EBV.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. REPLACEMENT P AR TS DIAGRAMS 9 15 16 17 3 3 4 2 2 12 7b O N O F F P I L O T L O H I 5b 1 8 19 18 1 3 20 1 4 b 2 1a 2 1b 1 4 a 1 0 b 1 0 a 7a 5 a 6.
TROUBLESHOOTING THE MILLIVOL T GAS CONTROL SYSTEM Note: Before troubleshooting the gas control system, be sure external gas shut off valve (located at gas supply inlet) is in the “ON” position. Important: Valve system troubleshooting should only be accomplished by a qualified service technician.
WARRANTY Y our gas appliance is covered by a limited warranty (see warranty certificate provided with appliance). Please read the warranty to be familiar with its coverage. Retain this manual. File it with your other documents for future refer - ence.
デバイスLennox Hearth EBVI30USの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Lennox Hearth EBVI30USをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLennox Hearth EBVI30USの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lennox Hearth EBVI30USの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lennox Hearth EBVI30USで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lennox Hearth EBVI30USを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLennox Hearth EBVI30USの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lennox Hearth EBVI30USに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLennox Hearth EBVI30USデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。