MicroBoards TechnologyメーカーPF-Pro Disc Printerの使用説明書/サービス説明書
ページ先へ移動 of 18
PF-Pro Disc Printer For Mac OS X Users Manual Microboards Technology LLC Version 1. 01.
• Introduction 2.
MICROBOARDS TECHNOLOGY, LLC PF-PR O Di sc Printer 3 TABLE OF CONTENTS INTRODUCTION ................................................................................................................... ........................................... 5 W HAT ’ S I NCLUDED .
• Introduction 4.
MICROBOARDS TECHNOLOGY, LLC PF-PR O Di sc Printer 5 Introduction The PF-Pro Disc Printer i s a robust automated inkje t CD and DVD printing solution. The PF-Pro Disc Printer has a 100-disc capacity, making the task of prin ting large numbers of discs fa st, easy and hands-free.
• Assembly and Installation 6 1 2 System Requirements The Microboards PF-Pro Disc Pri n ter has the following minimum requirements and compatibilities: Operating System Mac OS 10.
MICROBOARDS TECHNOLOGY, LLC PF-PR O Di sc Printer 7 Installing Ink Cartridges and Print Heads Supported Ink Cartridges The PF-Pro Disc P rinter uses 3 color and 1 black ink cartridges. The part numbers for these cartridges are PFP-HC-CYAN, PFP-HC-MAGENTA , PFP-HC-YELLOW, and PFP-HC-BLACK.
• Assembly and Installation 8 Loading Discs T h e n e x t s t e p i s t o l o a d y o u r P F - P r o D i s c P r i n t e r with output discs. The sy stem will accept CD o r DVD 120 mm (12 cm) inkjet printable discs. If the di sc does not have an inkjet p rintable surface, the ink will not adhere to the surface of the disc.
MICROBOARDS TECHNOLOGY, LLC PF-PR O Di sc Printer 9 Installation of Drivers and Software Driver Installation Drivers must be installe d on a hard disc. Once yo u have installed the software, sto re the original installer disc in a safe place. 1. Insert the Installation CD in your system’s di sc drive.
• Setting Printer Alignment 10 Setting Printer Alignment Alignment The PF-Pro Disc Printer system has been align ed at the factory, but may need to be adjusted depending on the type of media a nd media print surf ace on wh ich you are printing. Follow the se steps to adjust the alignment: • Click System Preferences in the Dock.
MICROBOARDS TECHNOLOGY, LLC PF-PR O Di sc Printer 11 Device Information This page shows the Firmware version and Serial Number of the PF-Pro Disc Printer. Clicking the Print Configurat ion Page button will print out a test disc. Clean The Clean page allows you to run a cleaning cycle on the ink cartridge.
• Microboards Printer Utilit y 12 Manual Pen Alignment Pen Alignment should be perform ed when a new printhead is installed. If you expe rience a decrease in print quality with an instal led printhead, you may need to perform this service. • Load 4 pieces of blank, unprinted media into the input hopper.
MICROBOARDS TECHNOLOGY, LLC PF-PR O Di sc Printer 13 Using the PF-Pro Disc Printer Creating Disc Labels The first step is to create a disc label of the co rrect size, 12cm x 12cm. You may use any applicatio n you prefer to create your labels. Included on the Installation disc are 2 eps-form at templates for you to use.
• Using the PF-Pro Disc Printer 14 Changing Print Quality To change the Print Qua lity, click the Advanced button on the Print screen. Select the Medi a type/Quality option from the list circl ed to the right. The settings to the right will appea r.
MICROBOARDS TECHNOLOGY, LLC PF-PR O Di sc Printer 15 Troubleshooting Printer not printing 1. Confirm the PF-Pro Disc Printer is plugged into a power source and is turned on. The ON/OFF switch is locate d at the back of the unit, above the power cabl e connector.
• Technical Supp ort 16 Printing Specifications Print Speed: Depends upon percentag e of coverage and print mode sele cted: • Approx. 45 seconds for 100% full- color coverage, Photo Normal Mode • Approx. 20 seconds for 100% full- color coverage, Text & Graphics Best Mode • Approx.
MICROBOARDS TECHNOLOGY, LLC PF-PR O Di sc Printer 17.
• 18.
デバイスMicroBoards Technology PF-Pro Disc Printerの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
MicroBoards Technology PF-Pro Disc Printerをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMicroBoards Technology PF-Pro Disc Printerの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。MicroBoards Technology PF-Pro Disc Printerの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。MicroBoards Technology PF-Pro Disc Printerで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
MicroBoards Technology PF-Pro Disc Printerを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMicroBoards Technology PF-Pro Disc Printerの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、MicroBoards Technology PF-Pro Disc Printerに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMicroBoards Technology PF-Pro Disc Printerデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
