Pellaメーカー818K0100の使用説明書/サービス説明書
ページ先へ移動 of 16
P art Number: 818K0100 ©2011 P ella Corpor ation INST ALLA TION INS TRUCTION - INSTRUCCIONES DE INS T ALACION WOOD HINGED P A TIO DOOR – (INCL UDES – ST AND ARD , PERFORMANCE UPGRADE AND HURRIC A.
Y OU WILL NEED TO SUPPL Y : T OOLS REQUIRED: • Cedar or Impervious shims/spacers (12 to 20) • 16d galvanized fi nish nails (1/4 lb.) • #10 x 3-1/4" corrosion r esistant wood screws (P erfo.
A. Confi rm the opening is plumb and level. Note: It is critical that the bottom is level. B. Confi rm the door will fi t the opening. Measure all four sides of the opening to make sure it is 3/4" larger than the door in width and 1/2" lar ger in height.
L. Bend each end of the center panel up. J. Make a 1" cut in each fold a t both ends of the sill pan. Note: T hese cuts will allow the edges of the sill pan to be bent.
2 PREP ARE THE DOOR FOR INST ALLA TION TWO OR MORE PEOPLE WILL BE REQUIRED T O HANDLE THE P ANEL AND FRAME SAFEL Y . A. Remove plastic wrap and car dboard packaging from door . Do not remove plastic shipping spacers. The shipping spacers will help keep the door squar e during installation.
6“ from end Lip #6 x 5/8” corrosion resistant screws 2B ALL DOORS • ALL DOORS • ALL DOORS • ALL DOORS 3 SETTING AND F ASTENING THE DOOR B. Cut and remove the str ap that runs from the door lock to the sill of the door. C. Insert the door from the e xterior of the building DO NOT slide the bot tom of the door into the opening.
Exterior 16d galvanized finishing nails D . Plumb and squar e door. Place shims at each hinge and lock strike location between the door and the sides of the opening.
of sealant into the three sill strike holes and install the thr ee # 8 x 3" fl at head stainless steel screws (pr ovided) into the holes. K. Shim between the frame and the rough opening at the head strik e location and at every frame anchor hole loca tion.
N. F or Doors with adjustable hinges: The hinges can be used to move the panel side to side by moving all hinges in the same direction or the hinges can slightly r otate the panel by adjusting the hinges in opposite directions.
6" 16" MAX O.C. 16" MAX O.C. 16" MAX O.C. 16" MAX O.C. 6" 6" 6" 6" 6" 6" 6" OUT -SWING DOUBLE OPERABLE 6" 6" 16" MAX. O.C. 5A 6" 6" 16" MAX. O.C. 5A 5B 5E 16" MAX O.
5F AP & HURRICANESHIELD PERFORMANCE UPGRADE & HURRICANESHIELD DOORS • PERFORMANCE UPGRADE & D. Secure the jambs and head of the door . Drive #10 x 3-1/2" corrosion resistant wood screws thr ough the door frame and shim, into the r ough framing.
7 SEALING THE DOOR T O THE EXTERIOR WALL CLADDING When applying siding, brick veneer or other e xterior fi nish material, leave adequate space between the door frame and the material for sealant. Refer to the illustra tion that corresponds to your fi nish material.
INTERIOR FINISHING If products cannot be fi nished immediately, cover with clear plastic to protect fr om dirt, damage and moisture. Remove any construction residue befor e fi nishing. Sand all wood surfaces lightly with 180 grit or fi ner sandpaper .
TROUBLESHOO TING - Adjustable Strik e Latching Issues 5 "#4 "EKVTUBCMFTUSJLFTIJN TJEFWJFX 4USJLF GSPOUWJFX "EK4USJLF4IJN FOEWJFX 'BDUPSZ JOTUBMMFE TJEF 4JEFUPCF VTFEJO *TTVF Issue 2: Door needs to close more tightly against the weather-strip .
T his page left blank intentionally ..
T his page left blank intentionally ..
デバイスPella 818K0100の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pella 818K0100をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPella 818K0100の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pella 818K0100の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pella 818K0100で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pella 818K0100を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPella 818K0100の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pella 818K0100に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPella 818K0100デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。