Primera TechnologyメーカーAP362の使用説明書/サービス説明書
ページ先へ移動 of 20
Quick S tart © 2009 All rights reserved Unpacking and Setup 3 Loading the Label S tock 4 Loading the Container 9 Applying the Label 12 Label Path Diagram 15 T roubleshooting and Maintenance 16 S peci.
Notices : The information in this document is subject to change without notice. NO W ARRANTY OF ANY KIND IS MADE WITH REG ARD TO THIS MA TERIAL, INCL UDING, BUT NOT LIMITED TO, THE IMPLIED W ARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A P ARTICULAR PURPOSE.
Thank you for purchasing the AP360 or AP362 Label Applicator (hereafter referred to as "Label Applicator"). Bottles, cans etc. will collectively be referred to as "containers.
1. Remove the Roll Bar and Roll Guides from the Label Applicator . The Roll Guides and Roll Drag Arm are removable and adjustable. They are held in place magnetically . (Figure 2-1.) 2. Remove one Roll Guide and the Roll Drag Arm from the Roll Bar . 3.
4. Place the Roll Drag Arm under the Roll Bar . The Roll Drag Arm may be placed on either side of the Roll Bar but the rounded tip of the Roll Drag Arm should be located in the center of the inside of the core. The arm is spring loaded so that there is downward pressure on the inside of the roll.
6. Now position the stock to correspond with the general area where it will be applied to the container . 7. Pull the loose end of the label stock forward and then push it into the F eed Area from the back of the label applicator . The labels will come out just under neath the P eel Edge.
9. T ak e the loose label stock and feed it between the Liner Idler Roller and the Liner Drive Roller . (F igure 2-7.) In order to feed the label stock between the rollers, the Liner Idler Roller should be in the unclamped position. F or some thicker label stock, it may be necessary to remove the labels from the liner before perfor ming this step.
11. If necessary , adjust the position of the liner on the P eel Edge left/right to align the liner with the label stock roll. Also, adjust the Label Sensor using the Label Sensor Bracket so that the Label Sensor Flag is roughly centered on the label stock.
AP360/362 Label Applicator 9 The AP360/362 can apply labels to a variety of containers including wine bottles, soda bottles, jars, cans, etc. Depending on the container type that you are labeling, you have several different options. Y ou may use the Container P ressure Ar m to hold the containers against the rollers, but that may not be necessary .
10 AP360/362 Label Applicator 3. Place the container on the Container Idler Roller and Container Drive Roller . Orient the container with the top to the left or the right, depending on the orientation of your labels on the label stock roll. (F igure 3-3.
AP360/362 Label Applicator 11 Important Note: F or bottles with a neck such soda, beer or wine bottles only one Container Guide can be used. Move the unused Container Guide to the far right or left side of the labeling area. F or cans or other containers that do not have a tapered neck, both Container Guides can be used, if desir ed.
12 AP360/362 Label Applicator A. Apply the Label 1. P ower on the Label Applicator using the P ower Switch. This can be done at any point with or without the container in place. 2. Place the container on the rollers using the instructions in Section 3.
AP360/362 Label Applicator 13 4. Press the F oot Switch to apply the labels. Both labels will be applied without pressing the F oot Switch again. T o set a value for another memory location, repeat this procedure. Note: The distance values are appro ximate.
E. Change the Unit of Measure between Metric and English. The AP362 can display measurements in both centimeters and inches. F ollow these steps to switch between the two. English (Inches): 1. T ur n off the unit. 2. Press and hold both the "Mode" button and the "+" button while you switch on the unit.
AP360/362 Label Applicator 15 Section 5: Label P ath Diagram Label Path Container Drive Roller Container Idler Roller Peel Edge Liner Drive Rolle r Liner Idler Roller Label Path Diagram.
T roubleshooting Labels are applied to the container cr ooked. 1. Check for container taper . Some containers such as wine bottles may have a slight taper that will cause the label to be applied crooked. Y ou may be able to apply your label straight if you angle the container idler roller to correspond with the angel of the taper .
Maintenance Label edges fold over or catch on the sensor as they are applied to the container . 1. Over time adhesive from the labels can build up on the sensor flag just above the container rollers. P eriodically clean the top of the sensor with a Q -tip and alcohol.
Container width: 1.0" to 9.4" (25.4mm to 238.8mm) Container diameter: 0.6" to 6.7" (15.2mm to 170.2mm) Container shape: Cylindrical and many tapered Supply roll diameter: Up to 8" (203mm) Media liner width: 1.00" to 8.38" (25.
AP360/362 Label Applicator 19.
P/N 511218 - 101609.
デバイスPrimera Technology AP362の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Primera Technology AP362をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPrimera Technology AP362の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Primera Technology AP362の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Primera Technology AP362で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Primera Technology AP362を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPrimera Technology AP362の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Primera Technology AP362に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPrimera Technology AP362デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
