Regencyメーカー510-994の使用説明書/サービス説明書
ページ先へ移動 of 10
P33 Zero Clear ance Direct V ent Gas Fireplace Model P33-NG4 P33-LP4 Fuel T ype Natural Gas Propane Minimum Supply Pressure 5” W .C. (1.25 kPa) 12” W .C. (3.00 kPa) Manifold Pressure - High 3.8” W .C. (0.95 kPa) 1 1” W .C. (2.74 kPa) Manifold Pressure - Low 1.
Model P33-NG4 w/ Contemporary Faceplate P33-LP4 w/ Contemporary Faceplate Fuel T ype Natural Gas Propane Minimum Supply Pressure 5” W .C. (1.25 kPa) 12” W .C. (3.00 kPa) Manifold Pressure - High 3.8” W .C. (0.95 kPa) 1 1” W .C. (2.74 kPa) Manifold Pressure - Low 1.
F r aming and Finishing 1) Determine the total thickness of facing material (e.g. drywall plus ceramic tiles) to allow the fi nished surface to be fl ush with the front of the unit. T otal facing thickness can vary from 1/2” (13mm) to 1-¼” (32mm) thick.
P33 Gas Fireplace Combustible Mantels with Contemporar y F aceplate Because of the extreme heat this fi replace emits, the mantel clearances are critical. Combustible mantel clearances from top of the louvers are shown in the diagram below . Mantel may be installed anywhere in the shaded area or higher .
6-7/8" (173mm) dia. Flue pipe 4" (102mm) dia. flue pipe W all Thimble (2 pc) T ermination Cap (Part# 946-523/P) AstroCap TM spring spacer FPI Direct V ent System (Flex) Horizontal T erminati.
Rigid Pipe V enting Horizontal or V ertical T erminations V enting Ar r angements - V er tical T er minations Rigid Pipe System (Propane & Natural Gas) The P33 is approved for a maximum 40 ft. straight vertical, with Rigid Pipe vent systems for Propane and Natural Gas.
V er tical V enting with Two (2) 90° Elbo ws - Initial v er tical section. T wo 45° elbows = One 90° elbow Option V H V+ V1 Maximum total pipe: length, of all sections, must not exceed 30 feet. T otal horizontal sections must not exceed 8 feet. Minimum of 1 foot between 90° elbows is required.
V enting Ar r angements - Horizontal T er minations This lightly shaded area of the diagram shows allowable combinations of vertical runs with horizontal terminations, using one 45° and one 90° elbow (two 45º elbows equal one 90° elbow). Note: Must use optional rigid pipe adapter (Part # 510-994) when using Rigid Pipe.
Horizontal V enting with Two (2) 90° Elbows - Initial v er tical section. T wo 45° elbows = One 90° elbow Option V H+ H1 Maximum total pipe: length, of all sections, must not exceed 30 feet. T otal horizontal sections must not exceed 8 feet. Minimum of 1 foot between 90° elbows is required.
Flex Liner Exhaust Flue A maximum of two certified joiner kits may be used per length. #948-305 35 ft (1 1m) Air Intake Co-linear DV V ertical T ermination Cap # 946-529 Co-Linea Flex Adapter with Kit.
デバイスRegency 510-994の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Regency 510-994をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRegency 510-994の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Regency 510-994の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Regency 510-994で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Regency 510-994を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRegency 510-994の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Regency 510-994に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRegency 510-994デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。