Remingtonメーカー476の使用説明書/サービス説明書
ページ先へ移動 of 20
REMINGT ON ® POWERHAMMER Model 476 Operating Instructions The Remington Powerhammer is de- signed for use with Remington Powder 22 caliber, Type A crimped loads and Remington Power Fasteners which are no longer than 63.
2 W ARNING: Safety Precautions BEFORE USING 1. ALWAYS handle the tool as if it were loaded. Before starting work, check that the tool is unloaded and the muzzle is clear. NEVER load a tool unless it is going to be used. 2. ALWAYS inspect to make sure the tool is working properly.
3 Safety Precautions DEFECTIVE WARNING POWDER ACTUATED TOOLS IN USE! G 018 G 018.
4 Safety Precautions HANDLING THE TOOL 1. NEVER place your hand over the muzzle. Accidental discharge can cause serious injury. 2. ALWAYS store UNLOADED pow- der actuated tool and loads in a locked container. Keep powder loads of different power levels in separate containers.
5 Safety Precautions PO W D ER LO A DS PO W D LO AD G 018 G 018 G 018 G 018 G 018.
6 3 . NEVER make fastenings in spalled or cracked areas. Safety Precautions KNOW YOUR FASTENING BASE MATERIAL 1. ALWAYS know the thickness and type of base material into which you are fastening. NEVER GUESS . Test the base material by using the Center Punch Test.
7 Safety Precautions ? ? ? ? CENTER PUNCH TEST Sinks in with average hammer blow TOO SOFT TOO HARD Point flattens Surface shatters Start 3 GREEN 2 BROWN 4 YELLOW CAST IRON GLASS TILE BRICK 1 GRAY TOO .
8 Safety Precautions 4. NEVER drive fasteners into thin or easily penetrated materials unless it is backed by concrete or steel. When in doubt, such as when base material is concealed, conduct a Center Punch Test. Check continu- ally to avoid fastening into unsuit- able material, especially in older buildings.
9 Safety Precautions 1” TOO THIN WELD 1/2” NO YES G 018 G 018 G 018 G 018 76 mm 3" 3X 1X 76mm 3" 76mm 3" 76mm 3" 5 mm MIN 3/16" 25 mm 1" 13 mm 1/2".
10 OPERATING THE TOOL 1. ALWAYS hold tool perpendicular to work surface. 2. Should the tool fail to fire, hold the muzzle firmly against the work sur- face for 30 seconds. Then remove the tool, eject the load and safely discard the misfired load into water or oil.
11 GAS LINE GASOLINE 482-49 POWDER LOADS 482-51 PO W DER LO ADS Safety Precautions 90 ° 30 WATER Spall Shield G 018 G 018 G 018 G 018 G 018.
12 6. Fasteners are a permanently in- stalled fixture. An act of demolition is required for their removal. Appro- priate safety precautions must be taken. Safety Precautions 2. Remington Powder Loads are available in four power levels with gray (1) being the lowest power level and yellow (4) being the high- est power level.
13 PO W D ER LO A DS 482-54 POWDER LOADS 482-55 YELLOW? BROWN ? GREEN ? GRAY ? NOTE: Failure to start with the lowest power level can result in overdrive condition and will result in damage to tool.
14 Safety Precautions 7. NEVER use fasteners longer than 63.5mm (2 1/2”). NEVER use com- mon nails. Remington Power Fas- teners are manufactured from spe- cial steel and heat treated to pro- duce a very hard, yet ductile fas- tener. 8. NEVER pry a load out of the cham- ber.
15 Safety Precautions Overdriven Fasteners An overdriven fastener results when too strong of a powder load is used causing the piston to extend past the muzzle. Move to the next lightest powder load. Repeated overdrive will damage your tool. By avoiding overdrive, you can ex- tend the life of your tool considerably.
16 LOADING THE POWERHAMMER 1. Insert the proper fastener into the muzzle, round metal head first. Push fastener until the point is even with the end of the muzzle. 2. Grab the muzzle and pull forward until it stops. This sets the piston and opens the chamber area.
17 Operation Spring Must Be Compressed Firing Pin Line Up Grooves Muzzle Firing Pin Grip Barrel Chamber LOADING FIRING EJECTING Continued.
18 CARE OF YOUR POWERHAMMER Clean your Powerhammer after each day’s use. Clean chamber with acces- sory wire brush, part number 56485. Apply good quality penetrating lubricant spray (such as WD-40) sparingly and wipe dry.
19 Limited W arranty DESA International warrants this Remington Model 476 POWERHAMMER against defects in materials and workmanship for a period of 30 days from the date of purchase.
101915-01 Rev. B 8/96 IMPORTANT This tool is designed to use Remington 22 caliber neck-down crimped loads, power levels 1 (gray) through 4 (yellow). Straight Wadded Power Load Neck-Down Crimped Power Load NOTICE: This is your Owner’s Manual. Read Carefully before operating your Remington POWERHAMMER Accessories Part No.
デバイスRemington 476の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Remington 476をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRemington 476の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Remington 476の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Remington 476で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Remington 476を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRemington 476の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Remington 476に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRemington 476デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。