SpaldingメーカーM682001の使用説明書/サービス説明書
ページ先へ移動 of 23
1 12/06 ID# M682001 © COPYRIGHT 2006 by SPALDING Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339 , For Europe: 00 800 555 85234 (Sweden: 009 555 85234 ), For Australia: 1-800-632 792 Internet Address: www.huffysports.
2 ID# M682001 12/06 BEFORE YOU ST ART T o ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. T est-fit large bolt s into large holes of elevator tubes, backboard brackets, and triangle plates.
12/06 ID# M682001 3 SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system.
4 ID# M682001 12/06 Get to know the basic parts of your basketball system... TOP POLE MIDDLE POLE BOTTOM POLE STRUTS ELEVATOR ASSEMBLY BACKBOARD BASE WHEEL CARRIAGE ASSEMBLY FRONT BACK RIM.
12/06 ID# M682001 5 Item Qty. Part No. Description 1 1 600053 Tank 2 2 908556 Strut, Pole to Base 3 1 904501 Handle Assembly 4 1 FR908356 Top Pole Section 5 1 FR908357 Middle Pole Section 6 1 FR908360 Bottom Pole Section 7 2 800332 Wheel Bracket 8 2 600056 Wheel, 3.
6 ID# M682001 12/06 #16 (2) #12 (1) #45 (1) #39 (2) #23 (4) #26 (4) HARDW ARE IDENTIFIER (BOL TS & SCREWS) #20 (1) #25 (2) #51 (2) #18 (6) HARDW ARE IDENTIFIER (NUTS & W ASHERS) #14 (12) #10 (.
12/06 ID# M682001 7 #44 (1) #46 (1) #47 (1) #13 (2) #30 (4) #49 (1) #50 (8) HARDW ARE IDENTIFIER (PLASTIC SP ACERS CAPS & CLIPS) HARDW ARE IDENTIFIER (OTHER) * You may have extra parts with this model.
8 ID# M682001 12/06 7 8 8 9 13 13 Complete wheel assembly as shown in Figure A. Secure wheel bracket (7) and wheel assembly (Fig. A.) to the tank (1) with a bolt s (18) and washers (24). 24 TO INSTALL SECOND PUSHNUT: • Assemble Pushnut, Wheels, Axle, And Wheel Bracket As Shown.
12/06 ID# M682001 9 Correctly identify each pole section. Poles have an identification sticker that will be used as a reference point in the next step. 2. Bounce middle pole section (5) into top section (4) using a wood scrap as shown until the top pole no longer moves toward the pole identification sticker on the middle pole.
10 ID# M682001 12/06 4. Bounce top and middle pole assembly (4 and 5) onto bottom pole section (6) using a wood scrap as shown. Bounce until the top and middle pole assembly no longer moves toward the pole identification mark on the bottom pole.
12/06 ID# M682001 11 6. Secure tank strut s (2) through center hole in pole as shown. 12 10 2 2 TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. W ARNING! IMPORT ANT! DO NOT TIGHTEN COMPLETEL Y .
12 ID# M682001 12/06 8. 42 6 14 16 15 IMPORT ANT! DO NOT OVER TIGHTEN! 7. 2 2 18 24 24 2 2 18 IMPORT ANT! DO NOT TIGHTEN COMPLETEL Y . TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
12/06 ID# M682001 13 Securely rest the assembly on sawhorse. Identify elevator tubes (32 and 35). 35 32 9. Toward Pole Toward Board 4 35 51 50 40 49 29 29 40 50 COMPLETED ASSEMBL Y 31 32 TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
14 ID# M682001 12/06 While still supported on sawhorse. Attach elevator tubes (32, 35) to backboard using sp acers (30), bolts (23), and nut s (31) as shown.
12/06 ID# M682001 15 2. 45 Insert T -bolt (45) into Slam Jam bracket (44) then, attach that assembly to board using bolts (26) and nut s (14). 14 26 27 IMPORT ANT! Carefully cut and peel protective film away from board prior to att aching rim.
16 ID# M682001 12/06 3. 29 31 36 35 35 W ARNING! USE EYE PROTECTION WHEN INST ALLING SPRINGS. 35 35 Support pole on sawhorse. Attach counter balance spring (36) to the spring support bracket (27) using bolt (51) and nut (31) as shown. Insert bolt (29) through left side upper elevator tube (35), then stretch spring (36) onto bolt (29).
12/06 ID# M682001 17 Inst all Slam Jam Rim to Backboard A. Fit rim (34) securely into bracket (44) as shown. Allow T -bolt (45) to slip through center hole in rim (34). B. Install reinforcement bracket (46) onto T -bolt (45) as shown. C. Install spring (47) onto T -bolt (45) as shown.
18 ID# M682001 12/06 Slide upper tube (17) onto handle assembly (3). Reinsert screws removed in previous step as shown. 5. 6. Remove packaging materials from handle assemblies (17 and 3). Remove screws on both sides of tube. 17 3 17 Screws r emoved in step 6 3 Rotate upper tube to line up screw holes.
12/06 ID# M682001 19 Install handle assembly (17) to lower elevator tubes (32) using bolt (29), spacers (50), and nut (31) as shown. Secure the handle assembly (3 & 17) to pole bracket (15) using bolt (20) and nut (10) as shown. 8. Secure the front panel (21) to struts (2) as shown with carriage bolts (22) and nuts (14).
20 ID# M682001 12/06 10. Roll completed assembly to desired position. Fill tank with water (approx. 40 gallons (128 Liters)) or sand (approx. 475 lbs. (216 kg)) and rotate the cap (41) into base (1). TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COU LD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
12/06 ID# M682001 21 Apply Height Adjustment and Moving Label (33) to front of pole, where it is clearly visible. 11 . 12. B. D. C. A. Install net (43). 34 39 28 Cover plate (28) will fit INSIDE back bracket. NOTE: 43 34 43 34 13. RIM COVER A TT ACHMENT 39 566 2 00 12 /05 H EI G H T A D JUS TMENT TO ADJUST BACKBOARD: 1.
22 ID# M682001 12/06 SECTION C: BOARD P AD Item Qty . Part No . Description 1 1 20157801 Board Pad, Left Section 2 1 20157901 Board Pad, Right Section 3 1 201580 Board Pad, Center Section 4 4 206081 Screw , Self Drilling, Hex Washer Head, 1/4 x .
12/06 ID# M682001 23 Using a portable drill (with adjust able torque) and a 5/16 socket and extension drill through the backboard frame and secure the pads in place with self-tapping screws provided. Use screws (7) for center pad and screws (4) for outer p ads It may be necessary to use an 1 1/16 drill bit (6) to pre-drill on some backboards (FIG .
デバイスSpalding M682001の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Spalding M682001をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSpalding M682001の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Spalding M682001の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Spalding M682001で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Spalding M682001を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSpalding M682001の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Spalding M682001に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSpalding M682001デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。