Stamina Productsメーカー55-1527Bの使用説明書/サービス説明書
ページ先へ移動 of 18
When calling for parts or service, please specify the following number : Model#: 55-1527, 55-1527B, 55-1527C W ARNING: T h e B u c k l e S t r a p a n d t h e N y l o n S t r a p m u s t b e attached and properly adjusted at all times during use of this product.
T ABLE OF CONTENTS Safety Instructions ...................................... 2 Before Y ou Begin ........................................ 4 Equipment W arning, Caution & Notice Labels ... 5 Hardware Identication Chart .................... 6 Assembly Instructions .
3 Call Us Fir st www .staminapr oducts.com 1 (800) 375-7520 Customer Ser vice THANK YOU FOR PURCHASING THE INVERSION T ABLE T o help you get started, we have pre-assembled most of your INVERSION T ABLE at the factory with the exception of those few parts left unassembled for shipping purposes.
BEFORE YOU BEGIN 4 Thank you for choosing the INVERSION T A B L E . W e t a k e g r e a t p r i d e i n p r o d u c i n g t h i s quality product and hope it will provide many hours of quality exercise to make you feel better , look better , and enjoy life to its fullest.
This chart is provided to help identify the warning, caution, and notice labels on the INVERSION T ABLE . Please take a moment to familiarize yourself with all of the warning, caution, and notice labels.
6 Part No. and Description Qty length length mm. in. INCHES This chart is provided to help identify the hardware used in the assembly process. Place the washers or the ends of the bolts or screws on the circles to check for the correct diameter . Use the small scale to check the length of the bolts and screws.
7 ASSEMBL Y INSTRUCTIONS Place all parts from the box in a cleared area and position them on the oor in front of you. Remove all packing materials from your area and place them back into the box. Do not dispose of the packing materials until assembly is completed.
ASSEMBL Y INSTRUCTIONS 8 SLOTS STEP 3 Slide the bottom of the two PIVOT ARMS(5) into the brackets located at each side of the MAIN FRAME(4). Align the desired hole on the arm with the peg on the bracket, and insert the peg into the hole to lock the PIVOT ARMS(5) in position.
ASSEMBL Y INSTRUCTIONS 9 STEP 5 Attach the FOOTREST(8) onto the HEIGHT ADJUSTMENT BEAM(6) with BOL TS(M8x1.25x50mm)(34), W ASHERS(M8)(38), and NYLOCK NUTS(M8x1.25)(36). NOTE: STEP 6 Insert the P AD TUBE(9) through the hole on the HEIGHT ADJUSTMENT BEAM(6) and secure with BOL T(M6x1x45mm)(32) and NYLOCK NUT(M6x1)(35).
SET UP INSTRUCTIONS 10 1. 2. A. C. B. BUCKLE 3. STEP 9: Attach the end of the NYLON STRAP(25) to the hook on the back of the MAIN FRAME(4); attach the end of the BUCKLE STRAP(26) to the hook on the FRONT FRAME(1), as shown in Illustration 2.
OPERA TIONAL INSTRUCTIONS 1 1 THE HANDLEBARS For added convenience, and safety , a set of HANDLEBARS has been added to the INVERSION T ABLE. These HANDLEBARS are located at the top of the REAR FRAME(2). The HANDLEBARS are to help you return to the upright position from any degree of inversion.
OPERA TIONAL INSTRUCTIONS USING THE INVERSION T ABLE 12 1. Check the decline angle before using the INVERSION T ABLE. T o increase the decline, lengthen the straps. T o decrease the decline, shorten the straps. W ARNING: DO NOT ALLOW table to invert past vertical.
OPERA TIONAL INSTRUCTIONS 13 Start by lying fully back on the bed with your hands at your side, or resting on your thighs. Keeping your hands close to your body begin to raise your arms slowly allowing the table to rotate backward. Stop, or lower your arms to control the downward rotation of the table.
ST ORAGE 14 FOLDING THE INVERSION T ABLE The INVERSION T ABLE can be easily folded for storage. T o fol d t he INVERSION T ABLE loosen the LOCKING KNOB(17) and pull out the LARGE SPRING PIN(16).
LIMITED W ARRANTY W ARRANTY Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship under normal use, service and proper operation for a period of 90 days on the parts and ve years on the frame from the date of the original purchase from an authorized retailer .
PRODUCT P ARTS DRA WING 16 FRONT BACK.
P ARTS LIST 17 P ART# P ART NAME QTY 1 Front Frame 1 2 Rear Frame 1 3 Folding Linkage 2 4 Main Frame 1 5 Pivot Arm 2 6 Height Adjustment Beam 1 7 Adjustable Instep Frame 1 8 Footrest 1 9 Pad T ube 1 1.
Model Number: ...................................................................................... Serial Number: ............................................................................................. Product Name: ...........................
デバイスStamina Products 55-1527Bの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Stamina Products 55-1527Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはStamina Products 55-1527Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Stamina Products 55-1527Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Stamina Products 55-1527Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Stamina Products 55-1527Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はStamina Products 55-1527Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Stamina Products 55-1527Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちStamina Products 55-1527Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
