Stanley Black & DeckerメーカーCS25/28の使用説明書/サービス説明書
ページ先へ移動 of 22
© 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 66205 8/2014 V er . 9 USER MANUAL Safety , Operation and Maintenance CS25/28 HYDRAULIC POLE CHAIN SA W.
2 ► CS25/28 User Manual DECLARATION OF CONF ORMI TY ÜBEREINSTIMM UNGS - ERKLARUNG DECLARATION DE CONFOR MITE CEE DECLARACION DE CONFO RMIDAD DICHIARAZIONE DI CONFORM ITA Hydraulic Tools _______ ___.
CS25/28 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an au- thorized and certied dealer .
4 ► CS25/28 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
CS25/28 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose.
6 ► CS25/28 User Manual POLE CHAIN SA W SPECIFIC SAFETY PRECAUTIONS • Do not rely exclusively upon the safety devices built into the saw . As a pole saw user , several steps must be taken to keep your cutting jobs free from accident or injury . • With basic understanding of kickback, you can re- duce or eliminate the element of surprise.
CS25/28 User Manual ◄ 7 The following guidelines must be followed to prevent accidental contact with overhead electrical conductors and/or communication wires and cables.
8 ► CS25/28 User Manual T able 2 – Minimum approach distances to energized conductors for persons other than qualied line- clearance arborists and qualied line-clearance ar - borist trainees. Nominal V oltage kV phase-to-phase 1) Distance ft-in m 0.
CS25/28 User Manual ◄ 9 SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL.
10 ► CS25/28 User Manual The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
CS25/28 User Manual ◄ 1 1 Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utili.
12 ► CS25/28 User Manual Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min.
CS25/28 User Manual ◄ 13 screw located in the top of the valve spool fully in (clock- wise) until it bottoms. TO DISABLE DUAL SPOOL OPERA TION AND CONVERT TO OC ONL Y OPERA TION T urn the selector screw located in the top of the valve spool fully out (counter-clockwise) until it hits the stop.
14 ► CS25/28 User Manual 4. WARNING W atch for falling limbs. Make a diagonal cut down to meet the horizontal cut and remove the wood from the notch. FELLING OR BACK CUT 5. The felling or back cut is made on the side opposite and at least 2 inches above the horizontal undercut (the felling cut is made higher as the size of the tree increases).
CS25/28 User Manual ◄ 15 PRUNING & TRIMMING 1. Observe all safety precautions. 2. Use both hands. Keep a rm grip. 3. Be alert for kickback. Do not allow the tip of the bar to touch anything while the chain is in motion. Figure 3. Crosscutting Logs/Limbs with Pressure on Bottom 4.
16 ► CS25/28 User Manual CHAIN TENSION ADJUSTMENT 1. Observe all safety precautions. 2. When the chain appears loose, lubricate it well and let it cool for a few minutes to allow for contraction of the chain. Disconnect the pole chain saw from its hydraulic power source.
CS25/28 User Manual ◄ 17 • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the OFF position when coupling or uncoupling hydraulic tools. Failure to do so may result in damage to the quick couples and cause overheating of the hydrau- lic system.
18 ► CS25/28 User Manual If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the pole chain saw , always make sure the hydraulic power source is supply- ing the correct hydraulic ow and pressure as listed in the table.
CS25/28 User Manual ◄ 19 Capacity CS25 and CS28 .................................................................................... 12 and 15 inch/30 and 38 cm Cut Lengths Weight (w/o Bar and Chain) .................................................
20 ► CS25/28 User Manual T o order complete motor assembly see “Note” on parts list (Page 21). CS25 / CS28 P ARTS ILLUSTRA TION.
CS25/28 User Manual ◄ 21 ITEM P ART NO. QTY DESCRIPTION 1 19212 1 CAPSCREW 2 65834 1 CHAIN GUARD 3 07631 2 NUT 4 08348 1 SA W CHAIN – 12 INCH 07641 1 SA W CHAIN – 15 INCH 5 66577 1 CHAIN GUIDE P.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
デバイスStanley Black & Decker CS25/28の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Stanley Black & Decker CS25/28をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはStanley Black & Decker CS25/28の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Stanley Black & Decker CS25/28の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Stanley Black & Decker CS25/28で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Stanley Black & Decker CS25/28を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はStanley Black & Decker CS25/28の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Stanley Black & Decker CS25/28に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちStanley Black & Decker CS25/28デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
