Stanley Black & DeckerメーカーHG60の使用説明書/サービス説明書
ページ先へ移動 of 18
© 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 67373 9/2014 V er . 6 USER MANUAL Safety , Operation and Maintenance HG60 HYDRAULIC BULL NOSE GRINDER.
.
HG60 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an au- thorized and certied dealer .
4 ► HG60 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
HG60 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs.
6 ► HG60 User Manual GRINDING WHEEL SAFETY • Ensure that the grinding stone is correctly mounted and tightened before use. • Operate the grinder at “no load” for 30 seconds in a safe position and ensure there is no vibration or other defects detected.
HG60 User Manual ◄ 7 SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL.
8 ► HG60 User Manual The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
HG60 User Manual ◄ 9 Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bu.
10 ► HG60 User Manual Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min.
HG60 User Manual ◄ 1 1 PRE-OPERA TION PROCEDURES PREP ARA TION FOR INITIAL USE Each unit as shipped has no special unpacking or as- sembly requirements prior to usage. Inspection to as- sure the unit was not damaged in shipping and does not contain packing debris is all that is required.
12 ► HG60 User Manual • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the OFF position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hy- draulic system.
HG60 User Manual ◄ 13 Problem Cause Solution Grinder does not run. Hydraulic power source not functioning. Check power source for proper ow and pressure (7–10 gpm/26–38 lpm @ 1500–2000 psi/105–140 bar . Couplers or hoses blocked. Locate and remove restriction.
14 ► HG60 User Manual Wheel Capacity ............................................................................... 3 in. dia. × 5 in. long × 5/8-1 1 arbor (type 16-19) Pressure Range ..............................................................
HG60 User Manual ◄ 15 OIL FLOW IN HG60 P ARTS ILLUSTRA TION.
16 ► HG60 User Manual ITEM P ART NO. QTY DESCRIPTION 1 26229 1 CAUTION STICKER 2 06316 4 BUSHING 3 00178 1 O-RING* 4 73308 1 IDLER SHAFT KEYED 6 04031 2 DOWEL PIN 7 26212 1 NAME T AG 8 03249 8 CAPSC.
.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
デバイスStanley Black & Decker HG60の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Stanley Black & Decker HG60をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはStanley Black & Decker HG60の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Stanley Black & Decker HG60の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Stanley Black & Decker HG60で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Stanley Black & Decker HG60を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はStanley Black & Decker HG60の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Stanley Black & Decker HG60に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちStanley Black & Decker HG60デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。