Stanley Black & DeckerメーカーSK58の使用説明書/サービス説明書
ページ先へ移動 of 22
© 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 70744 8/2014 V er . 8 USER MANUAL Safety , Operation and Maintenance SK58 HYDRAULIC SINKER DRILL.
.
SK58 User Manual ◄ 3 SAFETY SYMBOLS .................................................................................................................................................. 4 SAFETY PRECAUTIONS .............................................
4 ► SK58 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
SK58 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs.
6 ► SK58 User Manual 02754 SK58 Name T ag 03786 GPM Sticker SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL.
SK58 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
8 ► SK58 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bu.
SK58 User Manual ◄ 9 Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity to limit max.
10 ► SK58 User Manual NOTE: If uncoupled hoses are left in the sun, pressure in- crease within the hoses may make them difcult to connect. When possible, connect the free ends of the hoses together . 5. Connect the hose from the air supply to the hose on the tool.
SK58 User Manual ◄ 1 1 8. After the rock bit has carved out a depression in the material being drilled, open the hydraulic valve le- ver fully . Readjust the motor control knob to obtain a good drilling speed. Adjust the air valve to ensure the cuttings are being extracted from the drill hole.
12 ► SK58 User Manual • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couples and cause overheating of the hy- draulic system.
SK58 User Manual ◄ 13 PROBLEM CAUSE REMEDY T ool does not run. Power unit not functioning. Check power unit for proper ow and pressure (7–9 gpm/26–34 lpm, 1500–2000 psi/105–140 bar . Couplers or hoses blocked. Remove restriction. Pressure and return line hoses reversed at ports.
14 ► SK58 User Manual ACCUMULA TOR CHARGING 1. Perform steps 1 through 4 of the accumulator test- ing procedure above. 2. Connect the chuck of the charging assembly to the charging valve on the accumulator tester or , if pre- ferred, remove the tester from the charging valve and connect the charging assembly chuck directly to the charging valve.
SK58 User Manual ◄ 15 Figure 2. Charging the Accumulator CHARGING THE ACCUMULA TOR.
16 ► SK58 User Manual Shank Size (SK581 10 Air , SK58120 W ater , SK58310 UW Air) .................................................... 4-1/4 in. × 1 in. Hex Shank Size (SK58130 Air) ..................................................................
SK58 User Manual ◄ 17 SK58 P ARTS ILLUSTRA TION.
18 ► SK58 User Manual ITEM P ART NO. QTY DESCRIPTION 1 04763 1 AIR TUBE (SK581 10/SK58130/SK58310 ONL Y) 04965 1 W A TER TUBE (SK58120 ONL Y) 2 07064 1 VENT PLUG 3 04964 2 HANDLE GRIP ASSEMBL Y 4 01.
SK58 User Manual ◄ 19 SK581 10 – 1 INCH × 4-1/4 HEX SHANK AIR SK58120 – 1 INCH × 4-1/4 HEX SHANK W A TER SK58130 – 7/8 INCH × 4-1/4 HEX SHANK AIR SK58310 – 1 INCH × 4-1/4 HEX SHANK AIR, UNDER- W A TER USE NOTE: USE P ART NUMBER AND P ART NAME WHEN OR- DERING.
20 ► SK58 User Manual For underwater hydraulic tools the applications are broken down into four quadrants depending on type of tool and method of operation. The types of tools are percussive and rotational, each with different characteristics allowing for dif- ferent depth operation.
SK58 User Manual ◄ 21 NOTES.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
デバイスStanley Black & Decker SK58の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Stanley Black & Decker SK58をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはStanley Black & Decker SK58の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Stanley Black & Decker SK58の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Stanley Black & Decker SK58で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Stanley Black & Decker SK58を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はStanley Black & Decker SK58の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Stanley Black & Decker SK58に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちStanley Black & Decker SK58デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。