暖炉 Stovax (P)8127**UCの取扱説明書

概要は説明書の次のページに

1ページ

Aspen, Chamonix & Tahoe Decorative Gas Basket Fires With upgradeable control valve Instructions for Use, Installation and Servicing For use in GB, IE (Great Britain and Eire) PR0726 Issue 2 (July 2004) IMPORTANT Do not attempt to burn rubbish in this appliance.
2ページ

2 CONTENTS PAGE APPLIANCE COMMISIONING CHECKLIST 3 USER INSTRUCTIONS 4 INSTALLATION INSTRUCTIONS 12 Technical Specifications 12 Site Requirements 13 Installation 15 Commisioning 22 SERVICING INSTRUCTI.
3ページ

3 FLUE CHECK PASS FAIL 1. Flue is correct for appliance 2. Flue flow test 3. Spillage test GAS CHECK 1. Gas soundness & let by test 2. Standing pressure test mb 3. Appliance working pressure (on High Setting) mb NB All other gas appliances must be operating on full 4.
4ページ

4 USER INSTRUCTIONS 1.1 Installation and servicing must only be carried out by a competent person. 1.2 In all correspondence, please quote the appliance type and serial number, which can be found on the databadge located on a chain beneath the control valve.
5ページ

5 5.1 Your fire is fitted with a control valve that can be easily upgraded to battery powered remote control. This upgrade can be fitted by anyone capable of simple DIY jobs and requires no special training. This upgrade can be obtained through your local Gazco stockist.
6ページ

6 7.3.3 Using the small beads, fill the fire to the top. See diagram 3. 7.3.4 Smooth out the fire beads, it is important to ensure that the fire is completely filled, level to the top. NOTE: if your fire needs more beads, then there should be some left over from the original installation, if not then more must be ordered from your Gazco stockist.
7ページ

7 7.5.1 Place 15 large square blocks in a solid mass in the centre of the burner tray as shown, ensure they fit tightly together. See diagram 9. 7.5.2 Place 18 small coals or pebbles around the edge of the tray as shown, ensure that there are gaps between each coal or pebble.
8ページ

8 USER INSTRUCTIONS 7.6.3 Place one large coal or pebble on top of the pilot shield, then place 10 alternating large and small coals or pebbles around the perimeter of the fire. They should sit on the bottom row of small coals or pebbles and rest against the inner mass of square blocks.
9ページ

7.7.4 Place log (No. 7) along the LH side of the tray, log (No. 9) along the RH side of the tray and place logs (No. 8 and 11) along the front of the tray as shown. Place the cone (No. 14) on the LH side of the burnt log. See diagram 20. 7.7.5 Place the large log (No.
10ページ

10 USER INSTRUCTIONS 7.8.5 Place one large log (No. 6) so that it rests on top of the rear and front logs to the LH side. Place the other large log (No. 6) so that it rests on top of the rear and front logs on the RH side and log (No. 8) so that it bridges the centre gap as shown.
11ページ

11 USER INSTRUCTIONS 7.9.6 Place the two thin logs (No. 12), one at each side sitting on the tray and resting against the previously positioned logs. Place one log (No. 9) at the LH rear resting on the base log, and one log (No. 8) at the RH rear. See diagram 32.
12ページ

MODEL GAS GAS INLET AERATION INJECTION BURNER INPUT GAS FLOW RATE TYPE CATEGORY PRESSURE SIZE SIZE PRESSURE(mb) (pre-set) (kW) (m3/hr) (mb) HIGH LOW HIGH LOW HIGH LOW NATURAL G20 20 mb 7.5mm 1100 9.0 2.6 12 6 1.11 0.56 TAHOE BUTANE G30 29 mb 3 * 15mm 400 16.
13ページ

13 INSTALLATION INSTRUCTIONS SITE REQUIREMENTS 1.1 The chimney or flue system must comply with the rules in force. 1.2 Fireplace opening up to 450mm (18") wide by 600mm (24") high will usually work with a 175mm (7") diameter flue. Larger openings will require bigger flues.
14ページ

14 4.1 This appliance must stand on a non-combustible hearth that is at least 12mm thick. 4.2 It must be fitted into a non-combustible opening. 4.3 These appliances must be hearth mounted into a fireplace opening conforming to National Standards. 4.4 The appliance must be firmly fixed to the hearth.
15ページ

15 IMPORTANT: ENSURE THAT THE APPLIANCE IS CORRECTLY ADJUSTED FOR THE GAS TYPE AND CATEGORY APPLICABLE IN THE COUNTRY OF USE. REFER TO DATABADGE AND TECHNICAL SPECIFICATIONS AT THE FRONT OF THE BOOKLET. FOR DETAILS OF CHANGING BETWEEN GAS TYPES REFER TO SERVICING SECTION 9.
16ページ

16 4.1 Your fire is fitted with a control valve that can be easily upgraded to battery powered remote control. This upgrade can be fitted by anyone capable of simple DIY jobs and requires no special training. This upgrade can be obtained through your local GAZCO stockist.
17ページ

5.4.3 Starting at the front, place 14 alternating large and small coals or pebbles around the perimeter of the fire, they should sit on the bottom row of small coals or pebbles and rest against the inner mass of square blocks.
18ページ

18 5.5.2 Place 18 small coals or pebbles around the edge of the tray as shown, ensure that there are gaps between each coal or pebble. Place one on top of the pilot shield.
19ページ

19 5.6.4 Place the remaining 4 large coals or pebbles on top of the square blocks, ensure that they lean against the central small coal or pebble and that there are gaps between each coal or pebble.
20ページ

20 INSTALLATION INSTRUCTIONS INSTALLATION It may be necessary to make small changes to the log positioning in order to achieve the most pleasing flame effect but the following guidelines should be followed. 5.8.1 Refer to the log identification chart and identify the numbers corresponding to the logs that have been supplied.
21ページ

21 INSTALLATION INSTRUCTIONS INSTALLATION It may be necessary to make small changes to the log positioning in order to achieve the most pleasing flame effect but the following guidelines should be followed. 5.9.1 Refer to the log identification chart and identify the numbers corresponding to the logs that have been supplied.
22ページ

22 INSTALLATION INSTRUCTIONS COMMISSIONING 6.1 Close all windows and doors to the room, check all controls, and allow fire to burn on maximum for 5 minutes. Test for spillage of flue products using a smoke match. Pass the lighted smoke match along the top front edge just inside the opening or canopy.
23ページ

23 SERVICING INSTRUCTIONS SERVICING / FAULT FINDING CHARTS This appliance must be serviced at least once a year by a competent person. All tests must be serviced by best practice as described by the current CORGI recommendations.
24ページ

24 SERVICING INSTRUCTIONS FAULT FINDING CHARTS IGNITION FUNCTIONAL CHECK 2 NO SPARK Ensure there is no debris around the pilot assembly, (e.g. coal, soot etc.
25ページ

25 SERVICING INSTRUCTIONS FAULT FINDING CHARTS PILOT WILL NOT STAY LIT OR FIRE GOES OUT IN USE Ensure there is no debris around the pilot assembly, (e.g. coal, soot etc.) Check for fluff in the pilot aeration hole. See diagram 13 arrow A in replacing parts section.
26ページ

26 2.3 To release the right hand side of the control cover insert a narrow blade screwdriver into the slot shown in diagram 3, lever it gently and pull from the right hand side at the same time. The cover will now come off, there is a small cylindrical spacer inside the cover, this must be kept and replaced on the fixing screw during re-assembly.
27ページ

27 2.5 replace with a new ignition lead following the same route as the old one. replace the valve cover and securing screw. 2.6 check the operation of the new ignition lead. 3.1 The piezo unit used on this appliance is not serviceable and unlikely to fail.
28ページ

28 5.1 Remove the thermocouple from the back of the control valve. See diagram 8 arrow B. 5.2 Undo the mag unit retaining nut. See diagram 8, arrow C 5.3 After removing the retaining nut, the mag unit can be tapped out and a replacement fitted. 5.4 Replace the mag unit retaining nut and tighten.
29ページ

29 8.1 Remove the fire, refer to section 1. 8.2 Disconnect the 2x8mm and 1x4mm gas pipe fittings at the back of the gas valve, arrow A and disconnect the thermocouple. See diagram 10 arrow B. 8.3 Undo the single screw that secures the left-hand side of the control cover.
30ページ

30 COMMON COMPONENTS Control Valve GC0096 Ignition lead GC0090 Magnetic Unit GC0092 Control Cover GC0087 Upgrade Kit 8455 Pilot Shield (Standard) GZ1368 Pilot Shield (Glass Granules) GZ4424 Small Clay Beads (0.5 ltr) CE0239 Small Clay Beads (1.0 ltr) CE0240 Large Clay Beads (1.
31ページ

31 SERVICE RECORDS 1ST SERVICE Date of Service:........................................................................... Next Service Due:....................................................................... Signed:................................
32ページ

Gazco Limited, Osprey Road, Sowton Industrial Estate, Exeter, Devon, England EX2 7JG Tel: (01392) 261999 Fax: (01392) 444148 E-mail: info@gazco.com A member of the Stovax Group.

Stovax (P)8127**UC説明書を読み、問題を回避しましょう

デバイスStovax (P)8127**UCの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：

デバイスを適切に使用する方法を知るため
製品Stovax (P)8127**UCの正常な動作を定期的に点検し、サービスを行う方法を知るため
Stovax (P)8127**UCが故障した時の対処法を知るため

Stovax (P)8127**UCをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはStovax (P)8127**UCの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Stovax (P)8127**UCの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Stovax (P)8127**UCで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。

Stovax (P)8127**UCを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はStovax (P)8127**UCの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。

ですが、ユーザガイドが果たす重要な役割の一つは、Stovax (P)8127**UCに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちStovax (P)8127**UCデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。

Stovax (P)8127**UC取扱説明書

URLを共有

類似の説明書

URLを共有

類似の説明書

概要は説明書の次のページに

1ページ

2ページ

3ページ

4ページ

5ページ

6ページ

7ページ

8ページ

9ページ

10ページ

11ページ

12ページ

13ページ

14ページ

15ページ

16ページ

17ページ

18ページ

19ページ

20ページ

21ページ

22ページ

23ページ

24ページ

25ページ

26ページ

27ページ

28ページ

29ページ

30ページ

31ページ

32ページ

Stovax (P)8127**UC説明書を読み、問題を回避しましょう

暖炉カテゴリの他の説明書

Vermont Casting 1990

Vermont Casting 2080

Vermont Casting 20DVT

Vermont Casting 2100

Vermont Casting 2160

Vermont Casting 2170

Vermont Casting 2465

Vermont Casting 2466

Vermont Casting 2547CE

Vermont Casting 3030