Sub-Zeroメーカー3 1 5 I Pの使用説明書/サービス説明書
ページ先へ移動 of 24
I NST ALLA TION &O PERA TION M ODELS 315I AND 315IP I CE M AKER.
SUB-ZERO ® is a registered trademark of Sub-Zero Freezer Company , Inc. As you follow these instructions, you will notice W ARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Sub-Zero equipment.
3 THANK Y OU Congratulations on the purchase of your Sub-Zero Model 315I ice maker (Model 315IP w ith drain pump). This restaurant-type ice maker is designed for home use. It produces the same high quality clear ice that you would e xpect from Sub-Zero.
4 SUB-ZER O MODELS 315I AND 315IP INST ALLA TION ICE MAKER REQUIREMENTS T o properly make and store ice, the Model 3 15I(P) requires access to air , potable water , 115 V AC electrical supply and a drain. The ice maker must be installed indoors, in a controlled environment.
5 Dimensions in parentheses are in millimeters unless otherwise specified. SUB-ZER O MODELS 315I AND 315IP INST ALLA TION IMPORT ANT NOTE: The floor under the i ce maker must be at the same level as the surrounding finished floor .
Dimensions in parentheses are in millimeters unless otherwise specified. 6 SUB-ZER O MODELS 315I AND 315IP INST ALLA TION PLUMBING REQUIREMENTS Rough in the water supply line. Connect a 1 / 4 ” O D copper line to the house supply . Be sure to use an easily accessible shut-off valve between the supply and the unit.
7 SUB-ZER O MODELS 315I AND 315IP INST ALLA TION MODEL 315I GRA VITY DRAIN The drain and inlet water tubes must be plumbed before connecting to the ice maker . R efer to the illustrations below . All horizontal runs of drain lines must have a 1 / 4 " (6) per 12" (305) fall.
Dimensions in parentheses are in millimeters unless otherwise specified. 8 SUB-ZER O MODELS 315I AND 315IP INST ALLA TION MODEL 315IP DRAIN PUMP 1) Place the ice maker in front of the installa- tion opening. Adjust leveling legs to the a pproximate height.
9 SUB-ZER O MODELS 315I AND 315IP INST ALLA TION INST ALLA TION IMPORT ANT NOTE: T urn on the water supply and check all fittings for leaks. Make sure the e lectrical harness is attached to the solenoid. L et your customer know that the ice maker will not fill with water immediately and that the first batch of ice produced should be d iscarded.
Dimensions in parentheses are in millimeters unless otherwise specified. 10 SUB-ZER O MODELS 315I AND 315IP INST ALLA TION INST ALLA TION SIDE P ANELS W ith Model 315I(P), you must securely fasten the side panels to the adjacent cabinets and floor . Panels should be fastened to the floor and walls using ’L ’ brackets (hardware not provided).
11 SUB-ZER O MODELS 315I AND 315IP INST ALLA TION INST ALLA TION DOOR P ANEL INST ALLA TION Y ou should be sure of the door panel size and placement before proceeding with the installa- tion. If you have questions, contact your S ub-Zero dealer or cabinet supplier .
12 Install the door panel by engaging the tabbed bracket to the door first and then sliding the hinge side hardware over the positioning screws. Y ou will have a 1 / 4 " inch adjustment, up and down, side to side, with this hardware.
13 Dimensions in parentheses are in millimeters unless otherwise specified. SUB-ZER O MODELS 315I AND 315IP INST ALLA TION If you are storing or disposing of your old refrigerator or freezer , please do it safely . Remove the doors or tightly secure the doors closed.
14 MODELS 315I AND 315IP FEA TURES Undercounter ice maker Model 315I has a gravity drain, while Model 315IP has a built-in pump to allow water to d rain into adjacent sink 24" (610) depth-true de.
15 SUB-ZER O MODELS 315I AND 315IP OPERA TION ICE CUBES T he ice cubes are tapered cylinders about 1 1 / 4 " (32) in diameter at the widest end; taper down to 1" (25) wide at the top; and are 1 1 / 8 " (29) h igh. When the ice maker is adjusted properly , there should be a 1 / 4 " (6) indent in the base of the cube.
16 SUB-ZER O MODELS 315I AND 315IP OPERA TION HO W THE ICE MAKER USES W A TER T he ice maker begins with a fixed charge of water that is contained in the reservoir . As the water is sprayed against the freezing surface, t he part of water that does not contain mineral impurities will freeze and stick to the ice cup molds.
17 SUB-ZER O MODELS 315I AND 315IP OPERA TION CLEANING THE ICE ST ORAGE BIN T he ice storage bin should be sanitized occa- sionally . It is usually convenient to sanitize the bin after the ice making system has been c leaned, and the ice storage bin is empty .
18 SUB-ZER O MODELS 315I AND 315IP OPERA TION ICE MAKER CLEANING CLEANING THE ICE MAKING SYSTEM 1 ) O pen the door and turn the ice maker control knob to OFF . Refer to the illustration on page 19 for location of the control knob. 2) Scoop out all of the ice; either discard it or save it in a ice chest or cooler .
19 SUB-ZER O MODELS 315I AND 315IP OPERA TION 1) Open the door and remove the control box c over . 2) Locate the cube size adjustment screw s hown in the illustration below . T o make fuller cubes, turn the screw clockwise about 1 / 4 turn. This will make the freezing cycle l onger .
20 SER VICE CENTER Contact your Sub-Zero dealer or check the Locator section of our website, subzero.com, for the authorized ser vice center near est you.
21 SUB-ZER O TROUBLESHOO TING GUIDE TROUBLESHOO TING GUIDE P R OBLEM POSSIBLE CAUSE POSSIBLE SOLUTION U nit operates I ce may be stuck in the evaporator Check water supply – filter may but no ice fa.
22 SER VICE INFORMA TION If you do need service, be sure to have the model and serial number of your unit when y ou call. Y ou’ll find these numbers on the model and serial number plate located on the left sidewall of the reservoir . For warranty p urposes, you will also need the date of installation and the name of your Sub-Zero dealer .
23 S UB- Z ERO F REEZER C OMP ANY P RODUCTS L IMITED W ARRANTY RESIDENTIAL USE ONL Y F ULL FIVE YEAR SEALED SYSTEM W ARRANTY LIMITED SIXTH THROUGH TWELFTH YEAR W ARRANTY ON THE SEALED SYSTEM FULL TWO .
17307901 8 / 2005 S UB-ZERO FREEZER COMP ANY , INC. P . O. BO X 44130 MADISON, WI 53744-4130 800-222-7820 SUBZERO .COM.
デバイスSub-Zero 3 1 5 I Pの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sub-Zero 3 1 5 I Pをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSub-Zero 3 1 5 I Pの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sub-Zero 3 1 5 I Pの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sub-Zero 3 1 5 I Pで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sub-Zero 3 1 5 I Pを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSub-Zero 3 1 5 I Pの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sub-Zero 3 1 5 I Pに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSub-Zero 3 1 5 I Pデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。