Sub-Zeroメーカー315の使用説明書/サービス説明書
ページ先へ移動 of 24
inst all a ti on and op e r a t io n MO D EL 3 15 i ce m aker ® inst all a ti on and op e r a t io n.
InTR O DUCTION T he Sub-Zero Model 315 is a restaurant-type ice mak er designed for home use . It produces the same high quality clear ice that you would expect from Sub-Zero . T his guide is intended as a resource for the installation and operation of the Model 315.
PRE-INST ALLA TIO N T echnical Information Y our Sub-Zero ice maker is designed and manufactured with the highest regard for safety and performance . It meets or exceeds the standards of UL, and CUL.
4 Pre-INST ALL A TIO N Pre-Installation Considerations Purer water will freeze first in the ice making molds . T he reason for this is that anything dissolved in water lowers the water’ s freezing temperature. T his concentrates most of the impurities in the ice mak er water reservoir where they may form hard deposits known as scale .
Pre-INST ALL A TIO N Moving the Unit IMPORT ANT NOTE: When you move the unit into the house using a hand truck or dolly , position the dolly on the side of the unit and secure the door so it does not open while transporting the unit. IMPORT ANT NOTE: The floor under the ice mak er must be at the same level as the surrounding finished floor .
6 INST ALL A TIO N Plumbing Model 315 – Gravity Drain Model T he drain and inlet water tubes must be plumbed before connecting to the ice mak er . All horizontal runs of drain lines must have a 1/4" per foot fall. An air gap will likely be required between the ice mak er drain tube and the drain/waste receptacle .
7 INST ALL A TIO N Plumbing Model 315P – Pump Model 1) Place ice mak er in front of installed location. Adjust leg levelers to approximately correct position. 2) Remove control knob , control panel and control access panel. 3) Route water inlet line from w all through ice mak er to the front.
INST ALL A TIO N Completing the Installation IMPORT ANT NOTE: T urn on the water supply and check all fittings for leaks . Mak e certain the electrical harness is attached to the solenoid. Let your customer know that the ice mak er will not fill with water immediately , and that the first batch of ice produced should be discarded.
9 9 IMPORT ANT NOTE: T here is a part, pack ed with the ice mak er , that is required for this procedure . 1) Remove the hinge cover . 2) Remove the door by removing the (4) screws that secure the door to the door hinges . 3) Remove the door hinges by removing the (4) screws that secure them to the cabinet.
10 INST ALL A TIO N Panel Installation T he Model 315 will easily accommodate a door panel as long as you follow these points . F or any door handle hardware , we recommend near center pulls on edge o.
Once you have located the proper position for the hard- ware , mark the holes , remove template , and drill pilot holes for mounting of the hardware . W e recommend start- ing the first few holes , positioning the hardware , drilling remaining pilot holes , and securing the mounting brackets with the #8 x 1/2" screws .
Knock-out 12 Hinge Cover Installation T his is to be completed after the unit is fully installed. IMPORT ANT NOTE: Install the 90 degree stop prior to installing the hinge covers . 1) Remove the backing paper of the adhesive pads and bond to the hinge as shown in the illustration.
13 INST ALL A TIO N Installation Check List T he importance of the installation of your Model 315 ice mak er cannot be overemphasized. T he proper installation of your unit is the responsibility of the selling dealer or installer .
14 OPE R A T IO N Initial Start Up 1) Remove control box cover . 2) Rotate timer shaft clockwise until the cam is in the harvest position (switch button out). 3) T urn on water supply . 4) With unit plugged in, rotate ice maker control knob to the ON position.
15 OPE R A T IO N Ice Production T here are two distinct cycles: freeze and harvest. 1 freeze cycle + 1 harvest cycle = 1 batch of 8 cubes . T he freeze cycle happens when water is sprayed against the freezing surface . T he harvest cycle is when the ice is released and water enters the ice mak er .
16 Cleaning IMPORT ANT NOTE: Never keep anything in the ice stor- age bin that is not ice; objects lik e wine or beer bottles are not only unsanitary , but the labels may slip off and plug up the drain. Never allow the ice mak er to operate without regular cleaning.
17 Cleaning the Ice Making System 1) Open the door and turn the ice mak er control knob to off . 2) Scoop out all of the ice , either discard it or save it in a ice chest or cooler . 3) P our 4 ounces of Sub-Zero ice mak er cleaner into the ice mak er reservoir .
ADJUST MENTS T here are three items that may be adjusted: cube size, bin ice level and harvest time . IMPORT ANT NOTE: Cube size and harvest time adjust- ments should only be done by a qualified service person.
19 19 ADJUST MENTS Bin Ice Level Adjustment When the ice mak er shuts off the ice level in the bin should be even with the metal tube inside the bin. If the ice in the bin is too high or low , turn the ice maker control knob to adjust the bin thermostat.
20 TROUBLESHOO TING Problem Possible Cause Probable Correction T he ice mak er does not operate T he ice mak er is unplugged Plug the ice mak er in Break er tripped or fuse is blown Reset break er/rep.
21 TROUBLESHOO TING Problem Possible Cause Probable Correction No ice falling in bin, but Ice may be stuck in the Check water supply – filter may be restricted ice mak er operates evaporator and the.
22 W ARRANT Y "Sub-Zero Protection Plan" Full 5 Y ear W arranty and Limited 6th Through 12th Y ear W arranty on the Sealed System Full 2 Y ear W arranty on T otal Product Full F ive Y ear W .
SER VI CE Service For Y our Ice Maker Please have model and serial number available . Contact your nearest Sub-Zero F actory Authorized Service Center in your area, your dealer or Sub-Zero F reezer Company , P .O. Box 44130, Madison, WI 53744-4130, call (800) 222-7820 or e-mail us at customerservice@subzero .
Sub-Zero Fr eezer Company , Inc. 4717 Hammersley Road Madison, Wisconsin 53711 (800) 222-7820 (608) 271-2233 E-mail: customerservice@subzero .com 315IO 3/03 ®.
デバイスSub-Zero 315の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sub-Zero 315をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSub-Zero 315の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sub-Zero 315の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sub-Zero 315で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sub-Zero 315を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSub-Zero 315の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sub-Zero 315に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSub-Zero 315デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。