VTechメーカーIS7121/IS7121-2/IS7121-22の使用説明書/サービス説明書
ページ先へ移動 of 16
1 User’s manual I S 7 4 1 DECT 6.0 accessory doorbell for use with VTech models IS7121/IS7121-2/IS7121-22 Congratulations on purchasing your new VTech product. Before using this product, please read Important safety instructions on page 13 of this manual.
2 Basic steps to install your doorbell 1 Install doorbell batter y 2 Doorbell po wer adapter instal lation 3 Add and regist er a doorbell 4 Doorbell location t esting 5 Doorbell wal l moun t install ation Parts checklist Your telephone package contains the following items.
3 2 Doorbell power adapter installation Loosen the screws and the metallic plates, then slide the metal part of the wires underneath the metallic plates as shown.
4 3 Add and register a doorbell You can add another new doorbell (purchased separately) to your IS7121 telephone system. This telephone system accommodates up to two doorbells. Each new doorbell must be paired to the telephone base before use. Press and hold /FIND HANDSET on the telephone base for about four seconds until the IN USE light turns on.
5 Before mounting the doorbell on a wall, make sure you test if the location you install the doorbell is in range, and adjust the camera angle to best suit your needs. You may unplug the AC power rst so that you can move around more conveniently to make the tests.
6 To adjust the shooting area, you may either relocate the doorbell in different height level, or adjust the camera angle (see below). To adjust the camera angle: Tilt the lever to adjust the angle of the camera lens. The camera lens can be adjusted to left, right or down, up to 10 degrees.
7 Use the two holes on the doorbell wall mount cover to mark the desirable installation location on the wall. 1. 5 Doorbell wall mount installation Make sure you have done Step 4 above before you mount the doorbell on the wall. If you drill the holes into a stud, go to Step 3.
8 Align the wall mount cover and screws with the holes in the wall (or stud). 3. Align Loosen the screws and the metallic plates to release the wires from the doorbell. Use a sharp object to open a hole on the soft plastic part on the doorbell wall mount cover, then route the power adapter cord through the hole.
9 Slide the metal part of the wires underneath the metallic plates as shown. Twist the screws to secure. 6. Wire with red end Wire with black end Screws Metallic plate Metallic plate If yo u a lre a d.
10 Tighten the screw Tighten the screw into the threaded socket at the bottom to secure. 8. Plug the adapter into the indoor domestic power supply. 9. Plug!.
11 After an extended exposure to cold, heat or humidity, the doorbell gasket rubber may become sticky. If you need to remove the doorbell from its wall mount cover in case of battery replacement or doorbell relocation, follow the steps below. Remove the screw at the bottom.
12 If you already have a wired doorbell installed, follow the instructions below to install your new IS741 doorbell unit. Turn off the power supply to the existing wired doorbell. Follow Step 1 through Step 6 in Doorbell wall mount installation from pages 7 to 10.
13 Important safety instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of re, electric shock and injury, including the following: Read and understand all instructions. Follow all warnings and instructions marked on the product.
14 Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless telephones): Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers.
15 How long is the limited warranty period? The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product .
16 FCC Part 68 and ACTA This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other things, a product identier in the format US:AAAEQ##TXXXX.
デバイスVTech IS7121/IS7121-2/IS7121-22の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
VTech IS7121/IS7121-2/IS7121-22をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはVTech IS7121/IS7121-2/IS7121-22の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。VTech IS7121/IS7121-2/IS7121-22の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。VTech IS7121/IS7121-2/IS7121-22で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
VTech IS7121/IS7121-2/IS7121-22を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はVTech IS7121/IS7121-2/IS7121-22の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、VTech IS7121/IS7121-2/IS7121-22に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちVTech IS7121/IS7121-2/IS7121-22デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。