BIXOLONメーカーSRP-770IIの使用説明書/サービス説明書
ページ先へ移動 of 25
User's Manual SRP-770II Label Printer Rev . 1.14 http://www .bixolon.com.
Rev . 1.14 - 2 - SRP-770II ■ T able of Content s Manual Information & Usage Precautions ※ ·································································· 3 1.
Rev . 1.14 - 3 - SRP-770II ■ Manual Information ※ Manual Informatio n & Usage Precautions This user manual contains basic information for product usage as well as for emergency measures that may be required. The following separate manuals provide more det ailed content on various t ※ echnological issues and areas.
Rev . 1.14 - 4 - SRP-770II ■ Safety Precautions In using the present appliance, please keep the following safety regul ations in order to prevent any hazard or material damage. W ARNING Violating following instructions c an cause serious injury or death.
Rev . 1.14 - 5 - SRP-770II CAUTION Violatin g following instructions c an cause slight wo und or damage the app liance . Do not use the printer when it is out of order . This can cause a fire or an electro cution. • Switch off and unplug the printer before calling your dealer .
Rev . 1.14 - 6 - SRP-770II ■ Other Precautions The copyright for this user manual and various other manuals is pr operty of the BIXOLON Co., Ltd. Any copying or conversion into electronic firm and saving of this material without the express written permi ssion of BIXOLON Co.
Rev . 1.14 - 7 - SRP-770II 1. Content Confirmation The following items should all be c ontained in the printer p ackage. Contact the dealer from which the purchas e was made if any it em is damaged and/or missing.
Rev . 1.14 - 8 - SRP-770II 2. Product Part Names Feed Button Cover Peel-of f Cover Lever Printer Head Paper Holder Paper Guide Peel-off Senso r Paper Gap Senso r Paper Cover Power Switch.
Rev . 1.14 - 9 - SRP-770II S A MS UNG L A B E L P R N T E R Dip Switch Auto Cutter (Option) IEEE1284 Receptacle USB Receptacle Fan-Fold Power Receptacle RS-232C Receptacle.
Rev . 1.14 - 10 - SRP-770II 3. Inst allation & Usage 3-1 Power Connection Connect power to the prin ter as shown below . 1) T urn off the printer power switch. 2) Check to see that the AC adapter voltage matches that of the power source. 3) Connect the AC adapter jack to the printer power connector .
Rev . 1.14 - 1 1 - SRP-770II 3-2 Interface Cable Connection Connect the interface cable as shown below . This printer supports the following communications interface st andards. - RS-232C (Serial) - IEEE1284 (Parallel) - USB 1) T urn off the power switch.
Rev . 1.14 - 12 - SRP-770II 3-3 Paper Installation 1) Open the Paper Cover . 2) S pread the paper holder and insert paper as shown. S A M S U N G L A B E L P R I N T E R 3) Keep note of paper printing direction. 4) Adjust the paper guide to the wid th of the paper .
Rev . 1.14 - 13 - SRP-770II 3-4 LED Display Feed button Paper feed or cancel the print job. LED The current printer st atus can be viewed. (Refer to below) The current printer status can be viewed via the printer ’ s LED display . 1) Green LED on - The printer wait s for the data from Host (PC) in normal mode.
Rev . 1.14 - 14 - SRP-770II 4. Self-T est The self-test checks whether t he printer has any problems. (Users cannot perform this procedure if using the printer ’ s label peel-of f option.) If the printer does not function pr operly , contact an authorized dealer .
Rev . 1.14 - 15 - SRP-770II 5. Fine T uning 5-1 Printer Settings with Dip switches The dip switches are located on the bottom of the printer. The dip switches are used to set the printer to perform various functions. Follow these steps when changing dip switch settings: 1) Turn the printer power switch off.
Rev . 1.14 - 16 - SRP-770II [T able 1] Dip Switch 1 No Functions Details Off 4.0 ips 1-1 S peed Selection On 5.0 ips 4 3 2 Density Off Of f Of f 13 Off Of f On 14 Off On Of f 15 Off On On 16 On Off Of.
Rev . 1.14 - 17 - SRP-770II 5-3 Gap Sensor Auto-Calibration Gap sensor auto-calibration is used when the pr inter does not detect a gap on the label paper correctly . Generally a printer is set to detect most of gap types but some times it fails to detect and keep feeding the paper without a stop when spec ial paper used.
Rev . 1.14 - 18 - SRP-770II 5-4 Gap Sensor Manual-Calibration Manual-calibration of media detection can be us ed when the printer cannot detect a media gap (or black mark) even after auto-calibration has been executed. Users can calibrate sensor parameters in det ail by using the utilit y program provided by the manufacturer .
Rev . 1.14 - 19 - SRP-770II 5-5 The Peel-Off This function is used to automatically separate labels from the liner . - The peeler is for Label Paper only . - When the peeler switch is on, labels are not printed if previous printed labels have been removed from the peeler .
Rev . 1.14 - 20 - SRP-770II 3) Adjust the paper gui des and close the cover . 4) T urn the printer off and back on..
Rev . 1.14 - 21 - SRP-770II 5-6 Using Fan-Fold Paper Insert paper through both the rear slot and guides. Adjust holders and guides to the width of the p aper . 1) Open the Dust Cover and insert paper . O P E N 2) Adjust Paper Holders to the paper wid th and fixed Paper Holders with fixing tool.
Rev . 1.14 - 22 - SRP-770II 5-7 Auto Cutter (option) Auto cutter should be used for conti nuous paper only . ( i.e. roll paper) 1. Open the Dip switch cover , and make the switch 1 number 7 “On”. (Refer to printer mode setting at Chapter 5-1.) 2. Put a paper roll into the printer and close the cover .
Rev . 1.14 - 23 - SRP-770II 6. Cleaning Head Paper dust on the heating elements may lower the printer quality. When dirty, clean the print head as follows: ※ CAUTION - Make sure to turn the prin ter power off prior to cleaning.
Rev . 1.14 - 24 - SRP-770II 7. Appendix 7-1 Specifications Item Description Printing Method Thermal T ransfer / Direct Thermal Printing Dot Density 203 dpi (8 dot/mm) Printing Width 25.
Rev . 1.14 - 25 - SRP-770II 7-2 Certification 1) EMC & Safety S tandards • Europe: CE EMC,CB-Scheme:IE C60950-1, GS: EN60950-1: 2001 • North America: FCC rules p arts 15B WARNING Use of an unprotected interface cable with th is printer conflicts with EMC st andards.
デバイスBIXOLON SRP-770IIの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
BIXOLON SRP-770IIをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBIXOLON SRP-770IIの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。BIXOLON SRP-770IIの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。BIXOLON SRP-770IIで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
BIXOLON SRP-770IIを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBIXOLON SRP-770IIの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、BIXOLON SRP-770IIに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBIXOLON SRP-770IIデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
