Craftsmanメーカー580.751651の使用説明書/サービス説明書
ページ先へ移動 of 28
OWNER'S MANUAL MODEL NO. 580.75165! PRESSURE WASHER._ "_ CUSTOME. HELPLINE HOURS: Mon,- Frlo 8 a.m. to 5 p.m (CST) CAUTION: Read and Follow all Safety Rules and Instructions Before Operating This Equipment CRRFTSMRN ° 6.
SAFETY RULES _ CAUTION: ALWAYS DISCONNECT SPARK PLUG WIRE AND PLACE WIRE WHERE IT CANNOT CON- TACT SPARK PLUG, TO PREVENT ACCIDENTAL STARTING WHEN SETTING UP, TRANSPORTING, ADJUSTING OR MAKING REPAIRS TO YOUR HIGH PRESSURE WASHER, TRAINING: • Engine exhaust gases contain DEADLY carbon monox- ide gas.
CONGRATULATIONS on your purchase of a Sears Crafts- man high pressure washer. It has been designed, engi- neered and manufactured to give you the best possible dependability and performance. _hould you experience any problem you cannot easily =,medy, please contact your nearest Sears Service Cen- t.
TABLE 0F CONTENTS SAFETY RULES ............................................................ 2 PRODUCT SPECIFICATIONS ...................................... 3 ACCESSORIES AND ATTACHEMENTS ...................... 5 CONTENTS OF HARDWARE PACK .............
ACCESSORIES AND ATTACHMENTS These accessories and attachments were available when the high pressure washer was purchased. They are also vailable at most Sears retail outlets and service centers. Most Sears stores can order these items for you when you ,_rovide the model number of your high pressure washer.
Main Unit CONTENTS OF HARDWARE PACK Parts packed separately in carton Parts Carton Guide Handle Assembly (packed in flat carton) Owner's Manual ( Parts packed in Parts Carton High Pressure Hose W.
ASSEMBLY Read these instructions and Operator's Manual in its en- tirety before you attempt to assemble or operate your new high pressure washer. Your high pressure washer has, for he most part, been assembled at the factory, except those )arts left unassembled.
ASSEMBLY • Attach wire support to two lower holes in guide handle with # 10 self-drilling screws and # 10 fiat washers (Fig. 3). The hose minder should be to the left and gun holder to the ri_ht. Be sure loop of support is pointing upward. Place vmyt cap onto gun holder.
OPERATION KNOW YOUR HIGH PRESSURE WASHER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR HIGH PRESSURE WASHER. Compare the illustrations with your high pressure washer to familiarize yourself with the locations of various controls and adjustments.
OPERATION HOW TO USE YOUR WASHER IF YOU HAVE ANY PROBLEMS OPERATING YOUR PRESSURE WASHER, PLEASE CALL THE PRESSURE WASHER HELPLINE AT 1-800-222-3136. STOPPING YOUR PRESSURE WASHER . First, move engine RUN/STOP switch to "STOP" posi- tion (Fig, 9).
OPERATION APPLIYiNG DETERGENT WITH ADJUSTABLE NOZZLE IMPORTANT: USE SOAPS DESIGNED SPECIFICALLY --OR PRESSURE WASHERS. HOUSEHOLD DETER- 3ENTS COULD DAMAGE THE PUMP. IMPORTANT: YOU MUST A'I-I'ACH ALL HOSES BE- FORE YOU START THE ENGINE. STARTING THE EN- GINE WITHOUT ALL THE HOSES CONNECTED WILL DAMAGE THE PUMP.
OPERATION ADD ENGINE OIL: * Place pressure washer on a level surface and remove one of the yellow Oil Fill Caps (Fig, 17) and add engine oil from the enclosed bottle unttl level is at point of overflowing. Check engine oil level before starting each time thereafter.
i ( FULL FIG. 19 OPERATION SENSING LOW PRESSURE RUN FIG. 20 - Once engine has started, place Safety Latch in OFF position. • Press trigger on gun and wand assembly. Water should spray out the nozzle. • Adjust nozzle for correct pressure and spray angle.
CUSTOMER RESPONSIBILITIES MAINTENANCE SCHEDULE RLL IN DATES AS YOU COMPLETE REGULAR SERVICE Every 25 Before Hours or MAINTENANCE TASK Each Use Yearly PRESSURE WASHER Check/clean inlet filter and screen XV Check highpressure hose. X Check detergenthose.
CUSTOMER RESPONSIBILITIES Purge Pump of Air and Contaniments: To remove the air from the pump, follow these steps: , Set up the pressure washer as described in the AS- SEMBLY section and connect the water supply. Remove the nozzle attachment from the gun.
CUSTOMER RESPONSIBILITES SERVICE AIR CLEANER A CAUTION: NEVER RUN THIS UNIT WITHOUTTHE ABk COMPLETE AIR CLEANER SYSTEM INSTALLED ON THE ENGINE. THIS COULD RESULT IN PRE- MATURE WEAR TO THE ENGINE. Your engine will not run propedy and may be damaged if you run it using a dirty air cleaner.
SERVICE AND ADJUSTMENTS ENGINE SPEED A CAUTION: ENGINE SPEED WAS PROPERLY AD- JUSTED AT THE FACTORY AND SHOULD RE- QUIRE NO ADDITIONAL ADJUSTMENT. DO NOT ATTEMPT TO CHANGE ENGINE SPEED.
SERVICE AND ADJUSTMENTS o I o Remove additional debris by back flushing water sup- ply through wand (Fig. 30). Back flush between 30 to 60 seconds. Turn wand to stream spray and move nozzle from low to high while flushing. Reinstall nozzle into the wand.
TROUBLESHOOTING CAUSE 1. Nozzle in tow pressuremode. PROBLEM Pump has following problems: failure to produce pressure, erratic pressure, chattering, loss of pressure, 2. low water volume. 3. 4. 5. 6, 7. 8, 9. 10. !1. Detergent fails to mix with spray.
60 Z o 0 "U (/} J 9" m m u) U) C m (n rn ::0 01 01 ,,.aw o_ (.11 m "4 Cn.
CRAFTSMAN 2200 PSI HIGH PRESSURE WASHER 580.751651 , REPAIR PARTS ITEM PART NO. ! 90507 2 95319(3 3 95456 4 96016 5 94944 6 93790 7 96542 8 96865 9 95165 10 93873 11 95963 12 93869 13 23707 14 96430A .
t-a t,J 4 I L ! I I I I I I I I I < < ). Z 8 "0 U) I 2: m,m Q -r "0 :o m U) U) C: :0 m :E U) 2: m :0 Ul O) ¢n ._L =0 m :o "13 2J -4 U).
CRAFTSMAN 2200 PSi HIGH PRESSURE WASHER 580.751651 REPAIR PARTS ITEM PART NO. 1 93871 2 96430-A 3 93869 5 95165 6 96865 7 96542 8 93790 9 95386 10 95217 11 96400 12 92479 13 93873 t 4 40945 15 94404 1.
4_ TO "C" 7 32 36 ! LT. aREEN 61 BLACK' IGNITION SYSTEM VvlTH LOW OIL 8HUT-DOWN (LOS) MODULE 43 58 -4 m.
CRAFTSMAN 2200 PSi HIGHPRESSURE WASHER 580.751651 REPAIR PARTS ITEM PART NO, QTY. DESCRIPTION M PART NO. DESCRIPTION ........... ^ -rv4aoT tvwheel Assembly use,a w,u, ,.. an_3 _real_ar _ar_, .... .... ,, .... F"*,,n It r_ '_ _ "_';.
CRAFTSMAN 200 PSI HIGH PRESSURE WASHER580.751651 REPAIR PARTS 3O 31 43 48 13 / 5 54 37 53 27 14 51 19 44 46 12 13 39 40 17 50 57 ITEM PART NO. 1 7638O 2 76389 3 78660 5 72683 6 90325 7 76390 8 83337 9.
CRAFTSMAN 2200 PSi HIGH PRESSURE WASHER 580.751651 REPAIR PARTS 4 3 4 3 ITEM 1 2 3 4 5 6 9 10 !1 I2 13 PART NO, 100-81671 105-81671 103-81671 104.81671 t O9-81671 106-81671 102-81671 10t-81671 108-81671 107-81671 4 DESCRIPTION REWIND STARTER HOUSING(1 REQ.
OWNER'S MANUAL MODEL NO. 580.751651 IF YOU NEED REPAIR SERVICE OR PARTS FOR REPAIR SERVICE CALL THIS TOLL FREE NUMBER 1-800-4,REPAIR (1-800-473-7247) FOR REPLACEMENT PARTS INFORMATION AND ORDERING, CALL THIS TOLL FREE NUMBER: 1-800-FON-PART (1-800-366-7278) CRRFTSMRN ° 6.
デバイスCraftsman 580.751651の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Craftsman 580.751651をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman 580.751651の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman 580.751651の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman 580.751651で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman 580.751651を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman 580.751651の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman 580.751651に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman 580.751651デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
