Graco Inc.メーカー800-232の使用説明書/サービス説明書
ページ先へ移動 of 16
INSTRUCTIONS-PARTS LIST e 802-776, This manual contains IMPORTANT WARNINGS and INSTRUCTIONS READ AND RETAIN FOR REFERENCE GRACO HYDRAlCLEAN 826 c Pressure Washer GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1444 @COPYRIGHT 1987 GRACO INC. .. , .. . .
WARNING HIGH PRESSURE SPRAY CAN CAUSE SERIOUS INJURY. FOR PROFESSIONAL USE ONLY. OBSERVE ALL WARNINGS. Read and understand all instruction manuals before operating equipment. FLUID INJECTION HAZARD This 'pressure washer generates very high fluid General Safety pressure.
EQUIPMENTMISUSE HAZARD General Safety Any misuse of the pressure washer or accessories, such as overpressurizing, modifying pans, using incompatible chemicals and fluids, or using worn or damaged pans, can cause them to rupture and result in fluid injection, splashing in the eyes or on theskin, or other serious bodily injury or propeny damage.
ASSEMBLYANSTALLATION SET-UP 1. Remove the two hood bolts, flats and locks, from the center bottom of each side of the hood. Pivot the hood open. 2. Position the handle into the end of the chassis closest to the wheels. Line up the four mounting outside of the chassis.
j I Water Supply CAUTION Before connecting the water supply to the pump, check your local plumbing code regarding cross-connection to the water supply. A backflow preventor, Part No. 801-133. is available to prevent the back flow of contaminated water intothefresh watersupply.
Chemical Injector Opsration . .. 8. Be sure that the control ring on ihe injector is open two full turns from the closed position. To control ring is open, it may be left alone. The check this, the hood must be opened. Once the chemical mixture is controlled by the chemical metering valves on the control panel.
SHUTDOWN. FLUSHING, AND STORAGE WARNING 2. If the pressure washerwill beexposedtofreezing ' To reduce the risk of serious bodily injury. Pressure Relief Procedure including fluid injection and splashing in the temperatures, drain all water out of the pump.
TROUBLESHOOTING CHART To reduce the risk of serious bodily injury, including fluid injection, splashing in the eyes or on the skin, or WARNING injUryfrOmmOVingparts, alwaysfollowthe Pressure Relief Procedurewarning on page7beforeproceeding. PROBLEM Low Pressure .
PUMP SERVICE .. WARNING To reduce the risk of serious bodily injury. including fluid injection. splashing in the eyes or on the skin, or .injury from moving parts, always follow the Pressure Relief Procedure Warning on page 7 before proceeding. c NOTE: The following metric wrenches are needed: M6, M10, M30 Allen wrenches.
4. Inspect the plunger shah for oil leakage from the crankcase. If leaking is obvious, replace the oil seals (214). Otherwise, DO NOT remove these seals as they cannot be reused. NOTE: available to replace both seals. Oil Seal Kit, part no. 801-658, is 5.
PARTS DRAWING DuBois 826, .. - .; ........ P/N 800-232 .... ... . ... ..... . ;. -. .:.. ,~ . C C " (Continued) 22 '26.
W WIRING DIAGRAM lOb(4) i3(Ref.) ;o 69 PARTS LIST DuBois 826, 800-232 REF. PART NO. NO. 1 602-664 2 802-637 4 800-118 3 801-666 5 801-935 6 801-957 7 801-129 8 801-388 9 802-699 10 801-103 ". 11 801409 12 801-090 13 801-875 14 801.605 ." 16 801-015 17 801-3fiA 18 801-546 20 802-704 19 601-214 ".
DuBois 826, 800-232 (Continued) PARTS LIST REF. PART NO. NO. ~. 23 24 26 25 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 41 44 43 45 46 47 48 49 50 52 51 53 54 55 56 58 57 60 59 61 62 63 64 85 801-937.
Pump, 801 -864 PARTS DRAWING L2z1 21 5' PARTS LlST Pump, 801 -864 REF. PART 201 801-651 NO. NO. 202 801-652 t t203 $204 801-470 $205 206 802-795 207 801-485 208 801-484 t'210 *209 '21 1.
PARTS DRAWING Chemical Injector, PARTS LIST Chemical Injector, 800-138 REF. PART NO. NO. 1 801-684 NIPPLE. Hex, brass, 3/8 NPT DESCRIPTION QTY. 1 2 801-686 O-RING 1 ~~ ~~~ - . ". . - 3 801-687 NOZZLE NO. 2 4 801-688 O-RING 5 801-689 CHEMJETBODY 6 801-690 SPRING.
THE GRACO WARRANTY WARRANTY Gram warrants all equipment manufactured by it and bearing it5 name to be free from defects in material and wwkmanship an the date of sale by an authorized Gram distributor to the original purchaser for use.
デバイスGraco Inc. 800-232の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Graco Inc. 800-232をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco Inc. 800-232の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco Inc. 800-232の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco Inc. 800-232で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco Inc. 800-232を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco Inc. 800-232の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco Inc. 800-232に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco Inc. 800-232デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
