Audiovoxメーカー128-7404Aの使用説明書/サービス説明書
ページ先へ移動 of 24
128-7404A 1 of 24 Page 1 Model APS-998 Owner ’s Manual IMPORT ANT ! In order to provide you with the highest level of security to your vehicle, this system is equipped with selectable manual override circuitry .
128-7404A 2 of 24 Page 2 Protected Push Button V alet/Override Switch 7-Function LED-Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / V alet / Arming Intrusion Alert With Memory Instant Siren.
128-7404A 3 of 24 Page 3 known as a code grabber , which will receive and store the signal from your keychain transmitter and re-transmit at a later time to disarm your system.
128-7404A 4 of 24 Page 4 The dash mounted LED begins to flash slowly . Parking Lights flash one time. Siren will not sound. If the siren "chirped" three times, sometime after arming, the exclusive delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired.
128-7404A 5 of 24 Page 5 Any mild impact to the vehicle’s glass will cause the alarm to sound a short series of warning tones. Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full 30 second alarm cycle.
128-7404A 6 of 24 Page 6 Parking Lights flash two times. If the parking lights flashed three times, then the alarm was triggered in your absence. Before turning the key on, examine the LED to identify which zone was triggered. Siren will not sound.
128-7404A 7 of 24 Page 7 2. Press and hold the valet pushbutton switch until the dash mounted LED turns on solid. The system will remain in the valet mode. 3. T o return to normal operation, press and release the pushbutton switch any time the ignition is on.
128-7404A 8 of 24 Page 8 Custom Code Programming Example: T o Change the code from the factory pre-assigned code of 1 1 to “52” you would do the following: 1. Disarm the system by use of the transmitter or by use of the emergency override sequence.
128-7404A 9 of 24 Page 9 1. Turn the ignition key on then off. 2. Within 10 seconds, press and release valet switch three times. 3. If the chirps were on before you started, then you will hear two chirps indicat- ing they have been turned off.
128-7404A 10 of 24 Page 10 4. S tage 3 (City Mode) In this mode, the pre-detect chirps will change from six pre-warning tones to a full 10 seconds of warning chirps. The full detect trigger duration will be reduced from 30 seconds to 15 seconds. NOTE: Setting the stage of the shock sensor will be effective for one arming cycle only .
128-7404A 11 of 24 Page 11 W ARNING! Be certain that the vehicle is outdoors before using this or any remote vehicle starting device. A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs.
128-7404A 12 of 24 Page 12 3. Within 10 seconds of step 2, activate the RF start command two times. (Push the second channel button of your keychain transmitter 4 times). The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is activated.
128-7404A 13 of 24 Page 13 This security system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are: Re.
128-7404A 14 of 24 Page 14 every time the vehicle's engine is turned off. This feature requires the system to be set up for turbo timer during installation. Consult with your installation center to be certain this feature was activated and how long the vehicle will continue to run, 3, 5, or 10 minutes after the ignition switch is turned off.
128-7404A 15 of 24 Page 15 will indicate count down timer based on the 5, 10, 15, or 20 minute run time set up by your installation center . When the unit shuts off the exhaust indication will turn off and the transmitter will play a melody . If text mode was selected, the screen will scroll the words Engine Running.
128-7404A 16 of 24 Page 16 true if the transmitter is set for vibrate mode. When the vehicle is armed, and a door is opened, or ajar , the transmitter will chirp 3 times, the lights will flash, and the dis- play will indicate a door trigger as shown on the previous page.
128-7404A 17 of 24 Page 17 ADDITIONAL REMOTE FEA TURES: The two way remote control unit allows you to access status information from the vehicle, check temperature, light the display , toggle the transmitter from beep tones to vibrate mode, initiate daily start timer , and temperature start.
128-7404A 18 of 24 Page 18 the transmitter will emit a tone confirming the feature is active. Note: the unit will start once and run for the prescribed time. If you require more frequent starting please refer to auto start up timer mode shown earlier in this guide.
128-7404A 19 of 24 Page 19 NOTE: Y our system is shipped with two transmitters, 1 two way , shown on the left and the one way transmitter , shown right.
128-7404A 20 of 24 Page 20 (j) Y ou can set the Countdow n T imer (k) Y ou can set the Alarm Clock (l) Y ou can set the Clock Y our transmitter has a battery indicator that is shown in the upper right corner of the screen as shown left. This icon indicates a new battery shown with 3 bars.
128-7404A 21 of 24 Page 21 Throughout this manual you will find screen shots where they apply if using the two way transmitter . If using the one way transmitter while the two way transmitter is within range of the vehicle, the two way transmitter will update it's screen.
128-7404A 22 of 24 Page 22 THIS P AGE LEFT BLANK INTENTIONALL Y.
128-7404A 23 of 24 Page 23 APS 998 SYSTEM FUNCTIONS A T A GLANCE DASH LED INDICA TORS RAPID FLASHING = P ASSIVE ARMING/ACTIVE REARMING SLOW FLASHING = ARMED OF F = DISARMED ON SOLID = V ALET MODE 3 FLASH...P AUSE = INT RUSI ON ZON E 3 2 FLASH...P AUSE = INT RUSI ON ZON E 2 1 FLASH.
128-7404A 24 of 24 Page 24 © 2006 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY 11788 128-7404A.
デバイスAudiovox 128-7404Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Audiovox 128-7404Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAudiovox 128-7404Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Audiovox 128-7404Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Audiovox 128-7404Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Audiovox 128-7404Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAudiovox 128-7404Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Audiovox 128-7404Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAudiovox 128-7404Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。