FriedrichメーカーP/N9359944072-01の使用説明書/サービス説明書
ページ先へ移動 of 20
AIR CONDITIONER FLOOR CONSOLE/ UNDER CEILING DUAL TYPE P/N9359944072-01 Français Español English OPERA TING MANU AL MODE D’EMPLOI MANU AL DE FUNCIONAMIENT O KEEP THIS MANUAL FOR FUTURE REFERENCE C.
En-1 CONTENTS SAFETY PRECAUTIONS ....................................... 1 FEA TURES AND FUNCTIONS .............................. 2 NAME OF P ARTS ................................................... 3 PREP ARA TION ....................................
En-2 FEA TURES AND FUNCTIONS AUTOMA TIC OPERA TION ● COOLING MODEL Merely press the ST ART/STOP button, and the unit will begin automatic operation in the Cooling or Dry mode as appropriate, in accordance with the thermostat setting and the actual temperature of the room.
En-3 Fig. 6 Fig. 5 Instructions relating to heating (*) are applicable only to “ HEA T & COOL MODEL ” (Reverse Cycle). NAME OF P AR TS Fig. 4 Fig.
En-4 Fig. 4 Remote Control Unit C SLEEP button D MASTER CONTROL button E SET TEMP ./SET TIME buttons ( ) F Signal T ransmitter G TIMER button H F AN CONTROL button I ST ART/STOP button J AIR FLOW DIRE.
En-5 PREP ARA TION CAUTION! ● T ake care to prevent infants from accidentally swallowing batteries. ● When not using the remote control unit for an extended period, remove the batteries to avoid possible leakage and damage to the unit.
En-6 Example: When set to COOL Example: When set to 88 ° F Example: When set to AUTO T o Select Mode Operation 1 Press the ST ART/STOP button. The indoor unit ’ s OPERA TION indicator lamp (red) will light. The air conditioner will start operating.
En-7 OPERA TION Instructions relating to heating (*) are applicable only to “ HEA T & COOL MODEL ” (Reverse Cycle). * During Heating mode: Set the thermostat to a temperature set- ting that is higher than the current room temperature. The Heating mode will not operate if the thermostat is set lower than the actual room temperature.
En-8 T o Use the ON timer or OFF timer 1 Press the ST ART/STOP button (if the unit is already operating, proceed to step 2). The indoor unit ’ s OPERA TION indicator lamp (red) will light. 2 Press the TIMER button to select the OFF timer or ON timer operation.
En-9 SLEEP TIMER OPERA TION T o Use the SLEEP timer While the air conditioner is operating or stopped, press the SLEEP button. Both the indoor unit ’ s OPERA TION indicator lamp (red) and the TIMER indicator lamp (green) will light. To Change the Timer Settings Press the SLEEP button once again and set the time using the SET TIME buttons.
En-10 ADJUSTING THE DIRECTION OF AIR CIRCULA TION Instructions relating to heating (*) are applicable only to “ HEA T & COOL MODEL ” (Reverse Cycle). V ertical (up-down) direction of airflow is adjusted by pressing the remote control unit ’ s AIR FLOW DIRECTION VERTICAL SET button.
En-11 SWING OPERA TION Begin air conditioner operation before performing this procedure. T o select V ertical airflow SWING Operation Press the AIR FLOW DIRECTION VERTICAL SWING button.
En-12 ● Before cleaning the air conditioner , be sure to turn it off and disconnect the power supply cord. ● Be sure the intake grille is installed securely . ● When removing and replacing the air filters, be sure not to touch the heat exchanger , as per - sonal injury may result.
En-13 When two or more air conditioners are installed in a room and the remote control unit is operating an air conditioner other than the one you wish to set, change the signal code of the remote control unit to operate only the air conditioner you wish to set (four selections possible).
En-14 TROUBLESHOOTING Instructions relating to heating (*) are applicable only to “ HEA T & COOL MODEL ” (Reverse Cycle). In the event of a malfunction (burning smell, etc.), immediately stop operation, disconnect the power supply plug, and consult authorized service personnel.
En-15 TROUBLESHOOTING Instructions relating to heating (*) are applicable only to “ HEA T & COOL MODEL ” (Reverse Cycle). Symptom Doesn ’ t operate at all: Poor Cooling (or *Heating) perform.
En-16 OPERA TING TIPS ● Should the power supply to the air conditioner be inter - rupted by a power failure, the air conditioner will restart automatically in the previously selected mode once the power is restored.
En-17 Instructions relating to heating (*) are applicable only to “ HEAT & COOL MODEL ” (Reverse Cycle). * ● During use of the heating mode, the top of the indoor unit may become warm, but this is due to the fact that coolant is circulated through the indoor unit even when it is stopped; it is not a malfunction.
9359944072-01_OM_es.p65 1/21/10, 1:56 PM 18.
F r iedrich Air Conditioning Co. 4200 N. P an Am San Antonio , T e xas 78218 USA T el. (210) 357-4400 F ax (210) 357-4490 Visit us at www . fr iedrich.
デバイスFriedrich P/N9359944072-01の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Friedrich P/N9359944072-01をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFriedrich P/N9359944072-01の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Friedrich P/N9359944072-01の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Friedrich P/N9359944072-01で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Friedrich P/N9359944072-01を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFriedrich P/N9359944072-01の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Friedrich P/N9359944072-01に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFriedrich P/N9359944072-01デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
