AutostartメーカーAS-1412の使用説明書/サービス説明書
ページ先へ移動 of 14
Notice The manufacturer will accep t no responsibility for any electrical damage resulti ng from imprope r installation of the product, be that either da mage to the vehicle itself or to th e Unit. This Unit must be installed by a certifie d technicia n using all safety dev ices supplied.
P. 2 Installation Guide AS-1412 Introduction This Guidebook conta ins all informa tion pertinent to t he installation. Most (if not al l) features are grouped in t he User Guidebook and therefore, should you need infor mation on a featur e, you should refer to the User Guidebook.
AS-1412 Installation Guide P. 3 Before You Get Started … Ƈ On vehicles with a manual Transmission, always ensure that all Doors will get the Unit out of Ready Mode. Switch the wir e used so that it is triggered by all Doors. Ƈ Make sure that the Parking Brake and Door Switch contacts work properly.
P. 4 Installation Guide AS-1412 Harness Description When connecting the Module, it is important to make sure that th e connector with the Ground w ire is connected first, before making the 12-volt con nections. Should the Unit be powere d up before being grounded, there could be seri ous damage to internal components of the Un it.
AS-1412 Installation Guide P. 5 5-Pin Secondary Harness Wire Description 1 BLACK (–) Chassis ground input This wire must be connected to bare, un painted metal (the Chassis or true Body ground). It is prefer able to use a factory groun d bolt rather than a s elf- tapping screw.
P. 6 Installation Guide AS-1412 Note: The system also gives a Disarm pulse on this wire before remote start. 6 BLUE / WHITE (–) L.E.D. output 2 V L.E.
AS-1412 Installation Guide P. 7 Ignition barrel). Option 4 (Smart Ignition Re-Lock): Connects to th e Negative Door trigger Input. When the Ignition Loc k Option or the Lo ck Only Option is enabled: after t he Brake Pedal is pressed and after a Door has been opened and closed, the Do ors will RE-LOCK .
P. 8 Installation Guide AS-1412 12 YELLOW (+) Glow-plug input (Cont.) -plug input on the Mod ule may be “timed ou t”. The Module will power up th e Ignition and Glow-pl ug circuits and simply wait.
The Programming Assistance Button (a.k.a. PAB.) The PAB is located on the side of the M odule. This push button mi mics the Hood-Pin switch in order to avoid having to get ou t of the vehicle and pr essing the Hood-Pin switch. The PAB will work only when the Hood is up.
P. 10 Installation Guide AS-1412 to re-enter all opti on selections for all functio ns of the Mode you are accessing. You may not skip Functions*. *NOTE: Pressing the Brakes at any given moment will save the s electio n(s) you have entered and will return you to the Programmi ng Center.
AS-1412 Installation Guide P. 11 Auto Tach Programming Procedure NOTE: If no tach has bee n programmed and the ,, button is pressed, there will be no start attempt and t he vehicle will give 5 flash es. If another Tach Progra mming is required, simply repeat the Auto Tach Programming Proc edures.
3. Test the Brake shutdown circuit : With the ve hicle running und er the Remote St arter, press and releas e the Brake Pedal. The Engine sh ould shut down i mmediately. If th e Engine continues to run, check the Brake Switch con nection. 4. OEM Alarm Control: Make sure the Module is able to arm and disarm the OEM Alarm (if applicable).
AS-1412 Installation Guide P. 13 Caution: The relay output rating on this Unit is 25 A at mo st. Defective OEM solenoid switches can sometimes draw up to 50 or 60 A, causing the 30 A fu se to blow. Always check your circuit with a proper measuring device.
P. 14 Installation Guide AS-1412 1. FLASH the hood pin switch. 2. In ten seconds or less, pr ess the Brake Pedal six times. 3. The Parking Lights will fl ash 8 times confirming the Reset. Table 6 On some vehicles, such as, BMW, and certain Volkswagens, etc.
デバイスAutostart AS-1412の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Autostart AS-1412をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAutostart AS-1412の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Autostart AS-1412の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Autostart AS-1412で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Autostart AS-1412を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAutostart AS-1412の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Autostart AS-1412に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAutostart AS-1412デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。