AutostartメーカーAS-1535 SHの使用説明書/サービス説明書
ページ先へ移動 of 19
Notice The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, be that either damage to the vehicle itse lf or to the Unit. This Unit must be installed by a certified technician using all safety devices supplied.
P.2 Installation Guide AS-1535 SH Table of Contents Introduction ..................................................... 3 Included in the Package ................................. 3 Before You Get Started … ............................... 3 Harness Description .
AS-1535 SH Installation Guide P.3 Introduction This Guidebook conta ins all informa tion pertinent to t he installation. Most (if not al l) features are grouped in t he User Guidebook and th erefore, .
P.4 Installation Guide AS-1535 SH Ƈ Never leave the keys in the car. Leave them on a workbench with a window rolled down. Ƈ Remove courtesy light fuse, if possible, to prevent battery drain. Ƈ The Programming Assistance Button (A.k.a. PAB.) The PAB is mounted on the side of the Unit.
AS-1535 SH Installation Guide P.5 6-Pin Main Ignition Harness Wire Description A RED +12 V Battery Connect to the largest 12 V supply wire at the Ignition harness.
P.6 Installation Guide AS-1535 SH NOTE: A Tach signal that is too low will cause the Module to “ over crank” and a Tach signal tha t is too high will caus e the Module to “under crank”. 3 GREY (-) Hood Switch input Connect this wire to t he Hood Pin-switch s upp lied.
AS-1535 SH Installation Guide P.7 7 WHITE / ORANGE (–) Starter Kill output The unit is equipped wit h a selectable passi ve- or active-arming Starter Kill circuit that will immobilize the vehicle when the system is armed. This wire will provide a constant 500-mA negative out put when the system is armed (locked by remote) or if remote started.
P.8 Installation Guide AS-1535 SH 9 (cont.) PURPLE (-) External Trigger Option 3 (Key Sense (-) Input): Connects to OEM Key Sense Wire. When the Key is detected in the Ignition Switch (Ground (-) signal on the OEM Key Sense Wire) the Starter Kill will not ARM even when it is set to Passive Mode.
AS-1535 SH Installation Guide P.9 12 (cont.) YELLOW (+) Glow- plug Light input (cont.) A diode must be added betwee n the negative Glow-plug trigger on the relay and the negative Glow-plu g wire of the car.
The Installer … The Module … 1- Press and hold the Hood pin for 4 s econds. 2- Let go of the Hood Pin. Parking Lights “ON” 3- While the Parking Lights are on, press down the Hood Pin once more.
AS-1535 SH Installation Guide P.11 The Module has t he ability to retain up to 4 different Transmitter codes; if a fifth Transmitter is programmed, the code of th e first Transmitter will be erased from memory. To erase all Transmitter codes from memory, you mu st perform a Module reset (See “Resetting the Module” on page 17 ).
P.12 Installation Guide AS-1535 SH Options Programming MODE 1 *indicates default setting FUNCTION 1 – Ignition-controlled Door Locks OPTION 1* Ignition Locks ENABLED OPTION 2 Ignition Locks DISABLED.
AS-1535 SH Installation Guide P.13 OPTION 2* Disabled OPTION 3 Disabled MODE 3 *indicates default setting FUNCTION 1 – Home Valet Mode OPTION 1 Home Valet ENABLED OPTION 2* Home Valet DISABLED OPTIO.
P.14 Installation Guide AS-1535 SH Close the Hood to cancel th e changes. Table 4 Auto Tach Programming Pr ocedure This process can be carried out inst ead of the co nvention al Tach Programming Pr ocedure. 1. Make sure all the connections are done properly an d that the Module has b een powered-up.
AS-1535 SH Installation Guide P.15 2. Test Hood Switch shutdown : with the vehicle running un der the Remote Starter, open the Hood; the vehicl e should s hut down.
Caution! Do not use mor e than one of t he three sets of jumper pins simultaneously. The relay output rating on this Un it is 25A max output. Defective OEM solenoid switches can sometimes draw up to 50 or 60A, caus ing the 30A fuse to blow. Using a digital voltm eter, check the Starter wire for amperage when vehicle is crank ing.
AS-1535 SH Installation Guide P.17 Turbo Mode This Option allows turboch argers to idle down: after the user le aves the vehicle, the E ngine will keep running for 6 0 sec. and then shut down (It is a 1-minute Idle Mod e). Safe Start (Child Safety Mode) ( OFF by default.
P.18 Installation Guide AS-1535 SH x With the Parking Lights o n, immediat ely push the Pin-switch 3 times. x The Parking Lights and L.E.D. will flash the five events stored in memory. Table 12 The first four playback codes are S tart Failure Events .
AS-1535 SH Installation Guide P.19 Note: “x” stands for one flash of the Parking Lights Diagnostics - Parking Lights Flash Rate Flashes Description 1 x Doors locked, Starter Kill ar med. x End of Run Time. x TRUNK button pressed x START signal received by the Module .
デバイスAutostart AS-1535 SHの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Autostart AS-1535 SHをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAutostart AS-1535 SHの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Autostart AS-1535 SHの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Autostart AS-1535 SHで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Autostart AS-1535 SHを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAutostart AS-1535 SHの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Autostart AS-1535 SHに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAutostart AS-1535 SHデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。