AutostartメーカーAS-6205 SHの使用説明書/サービス説明書
ページ先へ移動 of 20
Notice The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, be that either damage to the vehicle itse lf or to the Unit. This Unit must be installed by a certified technician using all safety devices supplied.
P.2 Installation Guide AS-6205 SH Table of Contents Introduction ..................................................... 3 Included in the Package ................................. 3 Before You Get Started … ............................... 4 Installation Points To Remember .
AS-6205 SH In stallation Guide P.3 Introduction This Guide contains all informatio n pertinent to the in stallation. Most (if not all) feat ures are grouped in the U ser Guide and therefor e, should y.
P.4 Installation Guide AS-6205 SH Before You Get Started … Ƈ On vehicles with a ma nual Transmission, always ensure that all Doors will get the Unit o ut of Ready Mode. Switch the wire used so that it is triggered by all Doors. Ƈ Make sure that the Parking Brake and Door Switch contacts work properly.
AS-6205 SH In stallation Guide P.5 6-Pin Main Ignition Harness Wire Description A RED +12 V Battery Connect to the largest 12 V supply wire at the Ignition harness.
P.6 Installation Guide AS-6205 SH “under crank”. 3 GRAY (-) Hood Switch input Connect this wire to t he Hood Pin-switch s upp lied. This input will disable or shut down the Remote Starter when the Hood is opened. It is also used for programming and therefore it is essential th at it is installed.
AS-6205 SH In stallation Guide P.7 7 WHITE / ORANGE (–) Starter Kill output The unit is equipped wit h a selectable passi ve- or active-arming Starter Kill circuit that will immobilize the vehicle when the system is armed. This wire will provide a constant 500-mA negative out put when the system is armed (locked by remote) or if remote started.
P.8 Installation Guide AS-6205 SH 12 YELLOW (+) Glow- plug Light input This positive input will monit or the Glow Plug Light in Diesel Mod e: it will wait until the Glow Plug Light goes out to crank the En gine. Connect to the side of the Glow Plug Li ght that is positive when the Light is on.
AS-6205 SH In stallation Guide P.9 output ON for a 30-second cycle and shuts off automatically unless the user presses LOCK and UNLOCK before the end of that cycle, at which point, the AUX2 output shuts off. x This output can also be us ed as Priority Door Unlock.
The Programming Assistance Button (A.k.a. PAB.) The PAB is located on the side of the Mod ule. This push button mimic s the Hood-Pin switch in order to avoid having to get out of the vehicle and pr essing the Hood-Pin switch. The PAB will work only when the Hood is up.
AS-6205 SH In stallation Guide P.11 The Module can only be programmed Function by Function . After selecting a Mode (from 1 to 3), you will be taken to the first Function of that Mode.
P.12 Installation Guide AS-6205 SH x All Doors unlock upon the 2 nd , 4 th , 6 th … pressing of the UNLOCK button. Mode 2 *indicates default setting Function 1 – Home Valet Mode OPTION 1 Home Vale.
AS-6205 SH In stallation Guide P.13 OPTION 2* Ignition Valet - ENABLED OPTION 3 Ignition Valet - ENABLED Horn Honk / Siren Timing (Optional) 1. Make sure that Mode 3 Function 4 Option1 or Option 3 is activated. 2. FLASH the Hood Pin Switch Before the 20 seconds have passed, 3.
P.14 Installation Guide AS-6205 SH Table 5 Multi-Speed Tach Progra mming No manual adjustments ar e necessary. However, you should go through the Tach programming pr ocedure every time a new Uni t is installed. 1. FLASH the Hood Pin Switch . 2. Press and hold the Brake Pedal.
AS-6205 SH In stallation Guide P.15 Away. A medium “tap” should trigger the Warn Away. A hard “tap” should trigger the Alarm. x All vehicles are different and th erefore tra nsmit shock level diff erently, if you are unable to set b oth zones to your satisfaction, referrer to p.
Caution! Do not use mor e than one of t he three sets of jumper pins simultaneously. The relay output rating on this Un it is 25A max output. Defective OEM solenoid switches can sometimes draw up to 50 or 60A, caus ing the 30A fuse to blow. Using a digital voltm eter, check the Starter wire for amperage when vehicle is crank ing.
AS-6205 SH In stallation Guide P.17 Safe Start (Child Safety Mode) ( OFF by default.) Requires the user presses the S TART button on the Tr ansmitter twice within 3 seconds in order to start the vehicle. If the Special Safe Start Mode is select ed (SWAP Start): x To start the vehicle, press the LOCK and UNLOCK butt ons simultaneously.
P.18 Installation Guide AS-6205 SH Disarmed Notification This feature will notify the user whe n the vehicle is left disarmed after Ig nition is turned off, or when the Module i s disarmed after being prev iously armed, the opening or closing of a Door will cause the Horn or the Siren to sound on ce after 10 sec.
AS-6205 SH In stallation Guide P.19 10 x = Alarm condition Intrusion Codes 1 x = Power-up Reset: Battery disconnected / reconnected or dead… 2 x = Doors intrusion 3 x = Shock Sense 4 x = Hood 5 x = .
P.20 Installation Guide AS-6205 SH Diagnostics - Parking Lights Flash Rate Flashes Description 1 x Doors locked, Starter Kill armed. x End of Run Time. x TRUNK button pressed x START signal received by the Module. x Cold Weather Mode cancelled. x Cannot start after maximum number of attempts is reached.
デバイスAutostart AS-6205 SHの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Autostart AS-6205 SHをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAutostart AS-6205 SHの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Autostart AS-6205 SHの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Autostart AS-6205 SHで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Autostart AS-6205 SHを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAutostart AS-6205 SHの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Autostart AS-6205 SHに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAutostart AS-6205 SHデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。