AutostartメーカーCT-3200の使用説明書/サービス説明書
ページ先へ移動 of 21
Please note: Button Ι is for the LOCK/UNLOCK functions . Button ΙΙ is for the START/STOP functions. Buttons Ι & ΙΙ (together) is for the TRUNK release function.
P. 2 Installation Guide CT-3200 Introduction This guidebook c ontains all informatio n pertinent to the inst allation. Most (if no t all) features are grouped in the user guidebo ok and therefor e, should yo u need informat ion on a featur e, you should refer to the user g uidebook.
CT-3200 Installation Guid e P. 3 order to avoid hav ing to get out of the vehicle and pressing the hood-pi n switch. The PAB will work only when the hood is up. ♦ inspect vehicle for any bo dy damage or electrical problem s ♦ always solde r and tape all connec ti ons .
P. 4 Installation Guide CT-3200 C RED (+) 12 V Battery Connect to the lar gest 12 V s upply wire at th e ignition harn ess. Ensure that the OEM power wire is fus ed for more than 30 A. NOTE: certain new vehicles hav e no suitable 12 volts source at the IGNITION switch (the 12 Volt wire is too sm all to supply th e necessary current).
CT-3200 Installation Guid e P. 5 There is also a negative p arking light output. Only one of these two different outputs needs to b e connected. 12-Pin Accessories Harness Wire Function Description 1 BLUE (–) AUX 3 ( Trunk) output 500 ma negative output.
P. 6 Installation Guide CT-3200 are pressed if the trunk pin stat e is unchanged (th e trunk was unopened) . Disarm is sen t only if the system was previo usly locked and armed.
CT-3200 Installation Guid e P. 7 starter motor while the glow-plug indi cator light is still on. The module will e ngage the starter motor as soon as the glow-plug li ght (+) goes out. • Minimum waiting time is 3 seconds. • Maximum waiting time is 25 seconds (appr ox).
The Programming Assistance Button (a.k.a. PAB.) The PAB is located on the side of the module. This pu sh button mimic s the hood-pin switch in order to av oid having to get out of the vehicle and pres sing the hood-p in switch. The PAB will work only when the hood is up.
CT-3200 Installation Guid e P. 9 Button Ι for Option 1, Button ΙΙ for Option 2, Buttons Ι & ΙΙ for Option 3. Table 3 Programming Options MODE 1 (* indicates default setting) FUNCTION 1 – I.
P. 10 Installation Guide CT-3200 This process can be carried out ins tead of the co nventional tach pr ogramming proc edure. 1. Make sure all t he connections are done properly an d that the Modul e has been powered-up. 2. With the Hood up (Ground on the Hood Pin line), s tart the vehicle using the key.
8. Idle Mode: Make s ure the vehicle pr operly goes into Idle Mode. Most comebacks are the result of misunderstandings about how a produc t works or performs. Take the time to pro perly explain all functions and features to the customers before they l eave the premises.
P. 12 Installation Guide CT-3200 seconds after shutdown, Sec ure Lock will re-lock all Doors once more ( arming the system again). Please note that most OEM systems will not rearm t he Alarm while th e Engine is run ning, but will lock the Doors.
CT-3200 Installation Guid e P. 13 Troubleshooting Poor Transmitting Range installed at lea st 7.5 cm (3 in.) from th e he best location . Install the antenna as far oise, airports, 12. vehicle ca n affect rang e as well; v ans in gener al have an especially or ran e signal from t he remote control).
P. 14 Installation Guide CT-3200 − It always better to strip more th an you need, than not enou gh. A common way cold solder joints happen is when not e nough plastic is stripped off the vehicl e's wire, so during the sol dering process the plastic from the wire mel ts and flows in to the connec tion instead of th e solder.
CT-3200 Installation Guid e P. 15 − When all of the wires hav e been connected, s older the connec tions. When the sol der has cooled, the conne ctions are then i ndividually tape d up, to isolate th em. − Return to the engi ne bay and route the start modul e wires to their corres ponding connecti ons.
P. 16 Installation Guide CT-3200 87A: Normally Closed ( N/C ). Wh en the coil is at res t, 87A is connected t o 30. 30: Common. Wh en the relay is a t rest, 30 is conn ected to 87A, when t he coil is energize d, it is then moved and makes contact wit h 87.
CT-3200 Installation Guid e P. 17 The vehicle circuits are Iso lated for a reason, the wi ring of the remote star module should reflect this.) The relay connections: 85: Connects in parall el to the Ignitio n 1 output from the remote start mod ule. This becomes the pos itive side of t he coil.
P. 18 Installation Guide CT-3200 Solution: A relay is used to inv ert the negative signal from the st art module to a p ositive signal before it is sent to the OEM switch. The relay connections: 85: Connects to the st art module's Trunk release output wir e.
CT-3200 Installation Guid e P. 19 30 : Connects to the vehic le's Trunk releas e wire. Comments : At rest the rel ay is not active and the vehicle' s Trunk release sw itch is allowed to operate normally. When the Trunk release b utton is pressed on the re mote control, the start module's Trunk release outpu t activates the re lay.
P. 20 Installation Guide CT-3200 The entire process should t ake less than 20 secon ds. 2. The car won't start by remote. • Does the light on t he remote light up when you press th e button? • Is the starter in val et mode? • Does the vehicle have passive antitheft security (PATS , VATS, PASSLOCK, TRANSPONDER)? 3.
CT-3200 Installation Guid e P. 21 16. The car doesn't s tart and the park lights flash 4 times. • Check brake circui t. • Check for blown rear p ark light (feedback ). 17. The vehicle runs for 8 seconds t hen shuts down. I have 12 volt s on starter wire the whole time but no over crank.
デバイスAutostart CT-3200の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Autostart CT-3200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAutostart CT-3200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Autostart CT-3200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Autostart CT-3200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Autostart CT-3200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAutostart CT-3200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Autostart CT-3200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAutostart CT-3200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。